#4 Banyan's HHO Dry Cell, How it's made!
Loading...
Loading...
62,506
Link to this comment:
Share to:
Uploader Comments (Banyan23)
see all
All Comments (10)
-
good idea, very cheap.
-
so, you would say that your disign is more efficient than the smak?
I can see much ammounts of current leakage between the holes in your plates.
-
Its good idea ! but id say much better if the plates were rigid , excellent idea with the tape for seperation , ew also found that 1/16 was a perfect size to use between plates as then the bubbles can actually get out . like your ingenuity though .
keith sinclair
-
only use stainless steel
-
i don't know how you made the foil work. i thought it would have just turned into an arcing disaster.
-
請問影片中的是鋁片還是銅片？或者是其他材質
Loading...
- 7:49Introducing the Joe Miracle Cell - 28 6 Inch Pl...by mattimber64,045 views
- 3:126x6 HHO Dry Cell In actionby bmeade824,446 views
- 0:42water as fuel : build your own hydrogen fuel cellby vsnniche21,887 views
- 10:00Free Heat for your Homeby Prince7641208,204 views
- 2:57Dry Cell HHO Plans Blueprints for Car HHO Gener...by SaveGasSaveFuel28,064 views
- 7:50Hydrogen at home (Voltage vs configuration)#31by markj3040,542 views
- 6:34Dry cell assembly 5by d3adp00112,904 views
- 9:59part 1. HHO Generator (Car running ONLY on HHO)...by zgymnast61,537 views
- 5:39drycell test 5by d3adp00118,533 views
- 7:06EBN - More fun with the HHO torch!by SmartScarecrow37,451 views
- 9:56advanced hydrogen HHO dry cell detailsby advancedhydrogen14,900 views
- 4:18012 HHO generator designs for testingby FIZZYH2O63,925 views
- 7:58The GREATEST HHO Design Plans EVER! Best Hydro...by SaveGasSaveFuel10,542 views
- 1:52HHO- Toyota Sienna Bigger Systemby FruitJablanski8,108 views
- 4:22Dry Cell Battery Box Ideaby hhoconnection75,941 views
- 2:56Make A Hydrogen Fuel Generator HHO Dry Cell Car...by SaveGasSaveFuel12,884 views
- 5:01How It's Made High-Performance Enginesby thatsmynamedude54,395 views
- 0:49HHO dry cellsby ssfuturescott26,508 views
- 6:21HHO Dry Cell Installed In 89 Ford Mustang #6by PeteDog44416,608 views
I currently have a smack design booster, and can't seem to get the production from it. What would the expected production from a dry cell such as yours?
mowerman54 3 years ago
Production is one thing. I like to compare my results in MMW. Gas production will depend on how much heat (Amps) your cell can take without melting, meaning how much electrolyte you put in your cell. The smack design is great but there is way too much volt leakage and give around 3.4 mmw which is average for a wet cell. Dry cell in general will give you 5 mmw and more, 7 been 100% efficiency. My cell gives me 5.4 mmw.
Banyan23 3 years ago
Excelente trabajo ,Thank you inspire me to improve my design and make my Dry Cell
the tape you use, is the rubber, which is common to use electric
You can give me any specification, or link, thanks
Jan San
jansan2007 3 years ago
You will find this tape in any hardware store in electric and/or pluming section. It is a 20 mil of an inch PVC tape. Use tow layer of it between the plates. That's all I can say so far! Hoppe it helps.
Banyan23 3 years ago
Thank you!
Banyan23 3 years ago