how to weld a 2g mig bend test plate part 1
Loading...
Uploader Comments (redneckman454)
Top Comments
-
lol @ every video has comments like "that would never pass test where I work".. .
No matter what someone does there's always gunna be someone saying you did it wrong. period.
I'd bet the majority of critics can't do half as well.
2 months ago 2
All Comments (87)
-
typical fuckin yanks. TWI motherfuckers!!!
-
CRAP CRAP CRAP. DONT TRY TEACHING SOMETHING YOU DONT KNOW HOW TO DO. DONT TRY TEACHING WHEN YOUR IN A WELDING PROGRAM. REMOVE THIS VIDEO PLZ!!!
-
geez lots of people are bossy with welding techniques on youtube. maybe the worst subject for trolls yet.
-
la terminacion no es prolija.
-
@49bluesman have you done a test like this? that comment makes me think not
-
I am a welding instructor and a welding inspector in Toronto.
I am a CWB qualified welder in GMAW in the horizontal position done in spray transfer.
I'm also all-position qualified (flat/horizontal/vertical-up& overhead) in GTAW, SMAW & FCAW!
Not sure where you are from but you don't know what you're talking about in regards to testing in Canada to the CSA Standard W47.1 & W59. There is no pre-qualified joint testing in GMAW for vertical or overhead.
I never mentioned anything about vertical s
-
you dont use spray transfer for any other position then flat...
i dare you to make a vertical test plate using spray transfer...
this guy was right to use short circuit transfer for his horizontal test
-
@TheMartinto Practice until your hands move smooth and steady.
-
why do you run it backhand?does it make it flater?
-
@redneckman454 Is this flux?
- 6:58
how to weld a 2g mig bend test plate part 3by redneckman45411,670 views
- 9:02
how to weld a 2g mig bend test plate part 2by redneckman45416,218 views
- 5:52
How to set up a welding certification bend test plateby redneckman45423,223 views
- 4:05
Lincoln Power Mig 255C welder (About it)by redneckman4549,351 views
- 2:39
Mig Welding Technique Taught by Old Timerby weldingtipsandtricks1,154,400 views
- 4:09
Gas Metal Arc Welding Vertical Uphill and Downhillby weldingtipsandtricks57,871 views
- 0:31
Welding Chassisby SimonButlerInfo30,847 views
- 5:59
Different Types of Weldingby weldingtipsandtricks369,939 views
- 3:29
Mig Welding Techniques for Uphill Welding Tested for Penetrationby weldingtipsandtricks78,078 views
- 4:47
Tig Welding Pipe 6g Certification Test Techniquesby weldingtipsandtricks218,907 views
- 3:13
С Днем Рождения!by aramida19641,945,916 views
- 4:18
flux coreby basis1305347,477 views
- 5:07
How to Mig Weld Overhead - MIG welding Tipsby weldingtipsandtricks32,799 views
- 3:37
mig welding technique for uphill welding by weldingtipsandtricksby weldingtipsandtricks72,904 views
- 4:05
Mig Welding - Short Arc - pushing vs pulling vs Spray Transferby weldingtipsandtricks43,474 views
- 5:53
How to stick weld: open root v groove butt joint 3G vertical upby xivietal666headx116,904 views
- 2:21
how to weld a rear endby oldchevyshed152,416 views
- 2:45
Mig welding tips: technique for seting Wire feed speedby weldingtipsandtricks115,177 views
- 4:22
ALUMINUM WELDING ROD DC Please look at ebay item # 380262892658 or 350388156484by 1930charles32,198 views
- 2:32
welders greek 1by dumis4s91,062 views
that would NEVER pass a guided bend test!
short circuit transfer may look good, but it WILL fracture if you cut coupons out of that and bend them
listen to the guys that have recommended spray transfer
that's why GMAW is not used much fro anything structural (aside from fitting)
* remember to use at least 85% argon in your shielding gas mix to achieve a spray transfer
good luck
welderbones 2 years ago 5
watch parts 2 and 3 u will see i bend it and it comes out perfect
redneckman454 2 years ago 2