Miller Diversion 180 and Everlast PowerTig 185 micro
Loading...
Uploaded by weldingtipsandtricks on Jul 5, 2011
http://www.weldingtipsandtricks.com/tig-welder-demo.html
The Miller Diversion 180 and Everlast 185 micro tig welders are both AC/DC tig inverters with most of the controls preset.
This is a demo on some of the features and drawbacks of each.
- 49 likes, 0 dislikes
-
Uploader Comments (weldingtipsandtricks)
All Comments (26)
-
@Ckallert I have a hobart 165i and i was able to change from wp17 to wp9. I took the cover off and I am pretty sure you can figure a way to make it work.
-
I strongly dislike the included torch.
I wonder how difficult it would be to install a weldcraft torch on it.
Anyone try it yet?
-
You make great videos sir!
-
Great video Jody ... You should a review of the Eastwood tig 200 it's a 200amp ac/dc welder comes with a foot pedal hand control and 3year warranty for 850 ship
-
You go Jody. Not many would have the nerve to get into this type of comparison, but you did and I think it was well done, objective and un-biased. I really liked the disclaimer up front and you stuck to it. Hats off to you man... Now if the rest of the junk talkers would just put up or shut up. life would be good. Bob
- 5:07
Miller Passport vs Hobart Trek 180 Mig Welder Reviewby weldingtipsandtricks15,537 views
- 5:30
Aluminum Welder demo - Miller diversion and Everlast powertig part2by weldingtipsandtricks12,393 views
- 3:02
Tig Welding Aluminum with a Tig Fingerby weldingtipsandtricks9,942 views
- 8:11
TIG Welding Overhead -How to Tig Weld Overheadby weldingtipsandtricks46,131 views
- 4:01
Miller MIG Weldersby StaceyDavidsGearZ12,973 views
- 3:25
Walking the cupby 522design5,710 views
- 4:13
TIG Welding 4130 Chrome-moly Tubingby nielsmiller313,858 views
- 1:29
The Hardest welding rods trick you will ever try.by jcr3rd63,146 views
- 8:40
Everlast PowerTig 185 Micro AC/DC TIG Inverter welder GTAWby everlastgenerator5,202 views
- 5:55
Aluminum Welding Training on your own at homeby weldingtipsandtricks306,436 views
- 4:22
ALUMINUM WELDING ROD DC Please look at ebay item # 380262892658 or 350388156484by 1930charles29,042 views
- 2:10
Aluminum Welding: Adjusting AC Frequency on the Miller Dynasty® for Improved TIG Welding Resultsby nielsmiller32,112 views
- 3:13
Miller Diversion 165 TIG Welder reviewby reflectionlabs7,260 views
- 0:45
Miller Diversion 165 Tig Welder (907005)by kmstools5,246 views
- 3:40
Tig Welding Techniques Steel Lap Joint and Butt Jointby weldingtipsandtricks57,728 views
- 2:22
Thread repairby baslundforreal255,023 views
- 4:57
TIG Welding an Aluminum Fuel Cellby nielsmiller7,264 views
- 2:26
Everlast Powerpro 256 Deliveryby mrprism883,492 views
- 6:30
Miller Diversion180 Unboxingby gamble19971,136 views
- 4:21
My TIG Welding Cartby mycanoe444,863 views
I was just wondering what your settings were on the Everlast? Argon psi and amp settings? Going to buy this welder to do aluminum. I also notice that with the aluminum your tungsten has a pretty sharp point and I was always told to use a round end. Is the sharper end more accurate? controllable?
Evanofthecosmos 7 months ago
@Evanofthecosmos , I was using a #5 cup , 3/32" 2% lanthanated tungsten, about 15cfh of argon.
I usually taper electrodes a bit for aluminum. With most inverters, you can set the ac balance and or ac frequency to where the electrode stays somewhat tapered with only the very tip rounded. It lets you pinpoint the arc better than a ball....especially at low amperage on edges, and thin stuff. To get the thick aluminum to puddle hotter, I used argon helium mixed at around 50/50
weldingtipsandtricks 7 months ago
Is there any way to use another Torches on the Diversion?
Ckallert 7 months ago
@Ckallert you can change out the torch head, but I think you stuck with the body.
weldingtipsandtricks 7 months ago
What was the cleaning action set at on the Everlast welder % wise?
thewelderdude 7 months ago
@thewelderdude about 70-75% dcen
weldingtipsandtricks 7 months ago