ChipQuik - SMD rework
Loading...
Uploader Comments (zupnikal)
All Comments (15)
-
Make sure you put the new chips on the right way!
-
Hell yeah, can't have unfluxed solder / wick. Throw it away or use it on the xmas tree (and then throw it away).
-
It is a brand name for a special low melting point alloy. Normal solder will solidify withing 1 or 2 seconds after you remove the tip, whereas this stuff stays soft for 10 seconds or more. You mix it with the solder on parts you need to remove and just push them off as shown in the video. A starter set costs 16$ (lots of alloy, the amount of paste flux is a bit on the low side).
-
Of course.
-
Hm, I haven't seen any of these lately. It is basically just a "normal" analog regulated power supply upgraded with a small microcontroller to do some extras (like the keypad and RS232 interface to a PC). I think you'd have to invest about >200 for something like it. Nowadays you'd get a lightweight switching power supply and not a 10kg brick. But it will last for many many years, so the price is not that bad.
-
I got it more than 10 years ago, so I don't remember ;-)
6:52
Rework & Repair, Micro Assembly & Dispensingby airvaceng74,448 views- 2:33
Aoyue 852A+ SMD Rework Station Demo 2by flesknava76,417 views
- 0:37
Professional Surface Mount Soldering - How To: QFP 64 (Drag Solder)by jkgamm04153,242 views
- 0:53
SMD Chip Desoldering.mpgby vancovideo6,014 views
- 8:24
Hot-Air Soldering of Microchipsby ChipDipvideo31,799 views
- 0:36
Comprehensive online PCB repair guidebookby CircuitmartVideos64,366 views
- 4:20
hotplateby TheKhelben4,449 views
- 82 videoselectronica de consumo y varios
- 1:33
Desolder SMD without special toolsby MrKobalts82,472 views
- 1:08
Professional Drag Soldering: J-Lead PLCCby jkgamm04117,410 views
- 1:07
Reflow solder extreme close up (solder paste, hot air gun)by smbakeryt9,749 views
- 4:32
Desolder a SMD SOIC with only basic tools.by Mulletsrokkify22,262 views
- 3:20
Professional SMT Soldering: Hand Soldering Techniques - Surface Mountby jkgamm041209,761 views
- 1:34
RGB LED Toyby zupnikal7,088 views
- 2:06
Removing an IC With a Knifeby flesknava10,619 views
- 4:25
non infrared thermal smd soldering desoldering with a lampby 4madsat5,597 views
- 1:58
Surface Mount Solderingby jmstriegel198,342 views
- 2:50
Soldando SMD'sby xzakox60,955 views
- 4:51
Reflow Solderingby GuenaelJouchet19,321 views
- 0:40
Specialists in circuit board repair and reworkby CircuitmartVideos2,617 views
- 2:55
How to de-solder SMD surface mount components from laptop.by pchelp8883,387 views
I was pretty much cringing while watching you clean the excess solder with the desodlering wick. The way how you are rubbing it along the pads would be the fastest way to destroy them
DOTiSOalt 1 year ago
@DOTiSOalt: seems like everybody else is using abrasive scratch pads instead of solder wick. But what do I know.
zupnikal 1 year ago
Good work!
Is ChipQuik reusable??
0815tobey 2 years ago
Hmm.
If you took as much of it as I did in this video, the remaining blobs might work a 2nd time. Normally you only need very little of the alloy to soften the bond. I'm not sure if reusing makes any sense in that case. Unless you use it by the pounds.
zupnikal 2 years ago