How to replace washing machine controls in a Hotpoint washing machine
Loading...
Loading...
18,199
Loading...
There is no Interactive Transcript.
1:30
How to open a washing machine door that's stuck closedby eSparesVideo42,031 views- 1:06
Hotpoint washing machine sparesby eSparesVideo21,991 views
- 3:14
How a washing machine worksby eSparesVideo60,128 views
- 1:45
How to replace the washing machine dispenser drawer on a Hotpoint washing machineby eSparesVideo6,194 views
- 5:34
How to Replace a Indesit Washing Machine Door Lock, Interlockby Apart4u51,313 views
- 9:41
Washing Machine Drum Support or Spider How to Fit & Replace 4 of 4by Apart4u31,932 views
- 1:53
Kenmore / Frigidaire 417 model washer repairby batt40914,157 views
- 3:11
Brush type motor self destructingby ControlledExplosions18,771 views
- 1:01
Washing machine won't startby tompagenet18,317 views
- 3:15
Service Wash - Cure Washing Machine Smells & Remove Limescaleby RansomSparesltd81,882 views
- 0:42
How to repair Indesit washing machine that is Flashingby XR600RQJ9,916 views
- 5:47
How to replace a washing machine door seal on a Bosch washerby eSparesVideo115,452 views
- 5:14
Bosch WAE24164GB/30 Overviewby servisslimline15,681 views
- 1:17
How to replace Henry rear wheels on a Numatic Henry and Hetty vacuum cleanerby eSparesVideo43,754 views
- 0:51
How to replace & fit a washing machine drum paddle - Hotpointby RansomSparesltd7,134 views
- 2:14
How to replace a washing machine belt on a Bosch washerby eSparesVideo22,760 views
- 0:23
Noisy Washing Machineby schnell687,011 views
- 2:30
How to fit a control knob to my washing machine.by ezSpareVideos2,338 views
- 3:03
Dryer problems: How to fix a dryer that's not heating upby eSparesVideo85,876 views
My washing machine model is Sanyo ASW-50 Gt (neuro&fuzzy 50) It is not taking in water. There was smoke on start. What should I do. Is the solenoid not opening to allow water in or something else?
Rajkurrun 1 month ago
Actually, It isnt needed to make a picture of the PCB, Most connectors are asynmetric, This can be different on other machines through..
aeg12p 2 months ago
I don't have to replace the PCB I can troubleshoot that to component level and maybe salvage a part from a TV board or some other electronic board for free. I will post a video in the future how to pin point a defective electronic component.
tangnatalaga 8 months ago
@AUTubeN22 sorry i meant i have the wma 38 not the 36!!!!!
AUTubeN22 9 months ago
@SuperAlfie1000 hi i have the wma 36 washing machine and the first time i used it it sounded strained with the spinning not long after a few uses the wash cycles stopped i have to push the on button again and it commences with the cycle with no more problem! this is why i had to remove the pcb so maybe the button was defective but i cant really tell it looks fine!
AUTubeN22 9 months ago
when i clip the pcb back in place, the on off button will not depress! i can.t make sence of it or see any reason or obstruction! and how can i tell if the wash button/dial is in the correct position please? as you might guess i did not take a phone snap before taking off the wires but i am fortunate enought to own the wma 38 so ime glad to find you on here with the 36 version! :)p thanks for posting and any feedback you can offer!
AUTubeN22 9 months ago
the fascia looks new
SuperAlfie1000 9 months ago
87 78
SuperAlfie1000 9 months ago
87
SuperAlfie1000 9 months ago
78
SuperAlfie1000 9 months ago