drycell test 5
Loading...
Loading...
22,454
Loading...
Uploader Comments (d3adp001)
see all
All Comments (6)
-
wow, thanks!!!!!
-
i think i heard someone say that 6" 21 plate is the best for 12 volts, but for 8" plates 24 volts.
although i realize by balancing the volts & amps, it's the same, but over 6" plates, the voltage gaps are too low between plates.
-- your vids are good
-
what do you use as electrolyte? In my research caustics will do a number on neoprene. I have been working with EPDM and has great resistant qualities to heat and chemicals, But i dont know how it would work as spacers in a dry cell. May be slightly conductive.
-
well apparently the resoloution is on youtubes end.
Loading...
8:11
120v 4.5 LPM 60 plate hho ( hydrogen ) dry cell demonstrationby Alexthe2nd11,263 views- 5:23
Early EBN Dry Cell - My Benchtop Unitby dlwammo13,261 views
- 1:21
drycell test 6by d3adp00112,676 views
- 6:03
Chip komputerowy HHOby tedbucz9,523 views
- 1:05
100% water car engine (hho)by dreamyear224,165 views
- 1:19
HHO GENERATOR 1946by cyber1946159,128 views
- 6:41
12 volts turns water into Hydrogen fuel for driving, cooking and cutting metalby Javadavida109,688 views
- 1:01
Thailand, RSTDC : Hydrogen-Generators in Chiangmai Motor Show 2008(8)by tapingkae19,007 views
- 9:10
Hydrogen at home (Muddy Waters)#28by markj3018,090 views
- 0:57
hho explosionby iiimooo18,784 views
- 2:51
Dry cell assembly 4by d3adp00119,624 views
- 1:30
My new HHO Drycell project #5 Reservoir First runby jdcmusicman15,839 views
- 4:28
HHO 354 Plate Monster Hydrogen Generator Build Part 2by delvis1177,010 views
- 1:30
Dry cell assembly 1by d3adp00122,279 views
- 4:07
generator test 20 engine running on hhoby d3adp00128,919 views
- 0:57
HHO NEW DRY CELL WITH MANAFOLDby ssfuturescott58,511 views
- 9:30
EFIE and PWM Wiring Diagram for HHO Systemsby AlmostHydrogen354,462 views
- 5:05
Stanley Meyers easy to build Tubesby toranarod169,314 views
- 1:35
HHO 01by TribesTrike11,475 views
- 9:21
Hydrogen Tap ( More Pulse questions) 157by johnaarons45,849 views
What works best with the arrangement for holes where gas exits and water comes back into the cell?
partwerks 3 years ago
need to be more specific, what do you mean by works best with the arrangement for holes? Are you refering to flow?
d3adp001 3 years ago
this resolt of descoloration is acure after how much working time?
vshart 3 years ago
starts after a dozen or so hours, but it really is dependent on voltage. I overdrove these a little bit to find the bell curve in eff. The discoloration doesn't seem to affect performance.
d3adp001 3 years ago
What kind of gasket? and how thick are gaskets? Im currently testing a 8x8" dry cell with 1/16" gasket, also made 1/8th gaskets to try but have not tried yet, Thanks
johnmcphail1999 3 years ago
gasket material is neoprene, 60a hardness, and they are 1/16th thick.
Good luck, and if you can post some videos of the cell.
d3adp001 3 years ago