How to replace your Front pinion bearings on your truck Dana 60F
Loading...
Uploader Comments (briansmobile1)
All Comments (30)
-
nicely done! what a PITA job
-
@spelunkerd The vent tube is on the shifter housing. No spreader needed. The crush sleave on this one is a BEAST to crush. When the slop in the bearing is gone you stop crushing. You can do it with a vise and a hammer, but I strongly recommend a press for control.
-
This is surprisingly similar to the Dana 44, though I have never gone after that pinion seal. Is there a vent tube for this axle that you should check for patency? Did you need to use a spreader to get the diff back in? How do you get the correct torque/compression for that crush washer? If you don't have a press, can you do this job with hand tools?
-
@CODxFUNxMAN I have a few of them. Intake manifold gasket videos and head gasket videos.
12:25
How to pull a Jeep Cherokee 4.0L Engine briansmobile1by briansmobile13,118 views- 3:03
How to tell which bank is bank 1 and guess what's wrong gameby briansmobile19,426 views
- 6:11
BMW code P0442 Evap leak small How to fixby briansmobile13,158 views
- 8:27
2002 Chevy Tahoe Front Right Axle Seal How to Replaceby briansmobile120,398 views
- 1:25
bad pinion bearings.wmvby WarrenAutomotive12,043 views
- 5:52
Cavitacionby albertodelest61,207,031 views
- 0:06
Special Talentby NerdOnTheNet5,425,831 views
- 4 videosDifferential Rebuild
- 1:21
pinion noiseby aakjose79,378 views
- 4:45
Spider gear tilt causing "clunk"? (PLZ read desc.)by RedneckSophisticate18,407 views
- 1:14
8.5 10 Bolt Differential Problemby LS1COUPE4,671 views
- 1:21
How not to wake up your friends...by Deere61583,434 views
- 1:00
What causes front end vibration at high speeds on BMW 740iby MiniWorx16,775 views
- 1:36
busted dana 30 ring gearby TransAm7935985 views
- 5:23
Replacing of hub and wheel bearing Ford Transit 1091-10by WallmekAB17,039 views
- 1:20
Jeep flip over 8 times / after math slide showby masonjr37,594 views
- 12:18
MGB Differential Repair Part 2by mikeatyouttube13,347 views
- 11:18
Pinion Gear replacementby BorgfeldtCanada11,777 views
- 0:39
59400 Pinion Bearing Raceby autopartsdirecttoyou12,138 views
- 0:18
Chevy C10 12 Bolt Posi Rear End Damageby Eightbanger13,753 views
Good Video! Lots of useful information.
dieselboybc 1 week ago
@dieselboybc Thank you!
briansmobile1 1 week ago
Not a bad how to vid. But maybe you should get your "lovely assistant" to help with the recording. Just saying. Anyway, I'm getting ready to do my TJ Dana 44 front axle pinion bearings and seal. I dialed up this vid to see the spacifics on the how to put the pinion nut back to proper torque specs or get it close WITHOUT a torque wrench. One vid I saw said you should be able to spin the yolk about three times with a "flick of the wrist" when there is proper torque on the new bearings, (PRELOAD).
ironreign44 1 month ago
@ironreign44 Truthfully I'm lucky to get what help I did from my "lovely assistant." She was much more game to help and hang out when we were dating. Now.... I'll take what I can get.
briansmobile1 1 month ago
Climb the mountain!
Jk good video
chrism1367 3 months ago
@chrism1367 Back in the 1990's we had AMAZING roads to climb. No you have to drive 4 hours to Moab, Utah to get good climbing action. The Federal Gov't closed all the roads to prevent erosion.... and the roads all went soft and eroded away into ditches.
briansmobile1 3 months ago