Joels Burnout SR20DET gt2871r s13 nissan
Loading...
Uploaded by z3nk1dr1ft on Mar 17, 2009
Burnout in s13. GT2871R @15psi
3rd gear.
Uploader Comments (z3nk1dr1ft)
All Comments (43)
-
what a dippy fool , when you stand on the brake it's called a brake stand ...no burnout here, just a waste of tires to make smoke . perhaps you can't do a burnout .
-
sweet
-
@ddjernes ahhhh.... I see!! I will have to look into those!!
-
@SupraKid98 to hit 500 rwhp you need a gt35r really.
-
@ddjernes Well when it comes to the same turbo, like 5 pounds on a stock turbo isn't really going to make much, however, 20 pounds on that same stock turbo, will make quite a bit more power!! Its not going to be a top-mount either, so I don't think I would be able to run a T-88!!
-
@SupraKid98 Boost pressure is completely irrelevant to power. air flow volume is what matters. So if you have a t-88 26 psi would give you like 700hp. but 26 psi on a gt25 would give you like maybe 300
-
@ddjernes I found out I could run 26 pounds on the turbo I want, so you think 26 psi would make close to 500 wheel hp?
-
A bone stock SR is good for 400rwhp. what you are talking about is easily worth 450rwhp.
-
@z3nk1dr1ft I am planning on doing an SR20 swap too, in your opinion, what do you think a safe hp. would be on forged pistons, steel headgasket, valves & springs, cams, resurfaced block? I want to run at least 450rwhp on like 20-25psi... you think it could handle it?
80 videosYouTube Mix for Hoobastank- 0:44
S13 SR20DET GT2871r, HKS Step one cams, idle and rev.by NCDropkickSquad10,173 views
- 0:16
240sx vs viperby twincamz132035,453 views
- 1:06
240 From Hellby MrSetoffoffset170,124 views
- 0:22
s13 Sr20DET vs LT4 Camaroby dagatez36,585 views
- 1:03
Skyline RB26DETT Swapped into S13 2wd burnsby truckadsjoe21,922 views
- 0:25
Sr20det vs Type Rby swoosh1882112,709 views
- 0:47
Nissan Hardbody SR20DET Aruba Driftby compcellsolutions103,316 views
- 2:18
SR20DET 240SX GT2871Rby mattm6315,167 views
- 0:44
RB26 GTST SKID 002by drifta69614,320 views
- 1:08
Skoda 130RS GT2871rby bierhanzel69,267 views
- 0:28
nissan 200SX SR20DET 0-170 1bar @ GT2871Rby bartekl01124,912 views
- 0:48
sr20det nissan turbo gt2871 335hp dynoby badhabitz310,782 views
- 1:01
s13 burnoutby curtisR3112,693 views
- 0:31
S13 240sx SR20det Dyno Videoby upSLIDEdown29,873 views
- 1:52
S13 240SX w/ SR20DET built by Z-Feverby FeverRacing113,062 views
- 0:58
Sr20DET motor pulls 14 PSI of boost GT2871Rby arisythila21,243 views
- 1:17
SR20DET S13 701WHP PTE6262 39-40PSI(FRP)by ajftl15,472 views
- 0:26
s13 sr20 gt2871r 15 psi lil take offby lsturboty1,670 views
- 3:44
S13 240sx SR20det startupby SipoSupra42,821 views
- 0:24
Mobnes Nissan 200sx s13 ca18det @ gatebil mantorp 2009 burnoutby mobne46,019 views
Damn.
I have a S13.5 with a S13 blacktop, it's stock(ish) right now, but I have a PE1420 Turbo (GT2871 Size) 550's and a Tial 38mm going on there.
You have a fairly built motor and I have stock internals, so I'm a little scared to crank the boost up to 14lbs or so. Do you have any dyno numbers on your setup?
I might just keep it on wastegate spring pressure (11.6lbs)
NCDropkickSquad 2 years ago
a stock SR is good for 400hp. I wouldnt hesitate to run 15psi on your setup. We are pushing about 350rwhp
z3nk1dr1ft 2 years ago