How to chip a Honda 92-95 ECU Part 2/3

To see the full DIY of this video log on to www.imperio-honda.net

This DIY is to chip the following ECU's:
P28 - 1992-1995 Civic EX/Si | Del Sol Si
P30 - 1992-1995 Del Sol VTEC
P61 - 1992-1993 Integra GS-R
P72 - 1994-1995 Integra GS-R
P75 - 1992-1995 Integra RS/LS/GS/SE
P05 - 1992-1995 Civic EX
P06 - 1992-1995 Civic DX

Sorry the DIY is in spanish. But just pay attention and look at each of the pictures and that will be enough to know how to DIY!

Category:

Autos & Vehicles

Tags:

• chipping
• honda
• ecu

[djrodriguezthizz]

just lil bit of advise when soldering put the tip on what your soldering heat the pin up and feed solder in on the opposite side good look be careful not to hold it there too long just barely to melt the solder also try flux makes the job way cleaner just personal experience :)

[Sk8eRPR]

@djrodriguezthizz Thanks for the comment. Is always good for other people who are looking to read and learn.

Thanks again for a really useful comment.

BTW I'm Rodriguez too! LOL! ;-)

[2383pollito]

i wish i knew how to chip ecus... im just learning how to chip ecs and this video really does give an idea on how to start, i have the same tools and and i just needed some one to teach me how to use them... thanks men nice work...

[Sk8eRPR]

@2383pollito This are two links.

Use COPY PASTE

qcwo.com/technicaldomain/insta­lling-a-honda-p28-ecu-chip

Use COPY PASTE

xenocron.com/chipping-kit-w-ss­t-chip-obd1-ecus-p-277.html

[memopt2]

jamas habia visto algo tan estupido como trabajar soldadura en el suelo(piso)

[Sk8eRPR]

@memopt2 LOL! Y yo jamas habia visto algun comentario tan estupido como el tuyo.

[BABYGODZILLA2009]

Hi, great vid i must say, I have a D16 JDM Vtec setup (P08 ECU). I need to get this chipped, im very new to this so i could use your advice on this. On Ebay i found that u can get the chip programmed to your specifications, my question is, if this guy from ebay send me the chip with my program specifics, can i simply install the chip to my ECU (plug & play) and run it or do i have to do anymore stuff? Please help, i will be waiting for your reply.

[fiverrgigler]

Great video you have here. I've been looking something like this. I think I have problem with the ECU because one of the injector is not pulsating. I've swapped with the brand new injector but it didn't fix the problem. The wire shows no cut or problem. I think the transistor coming from the ECU might be causing the problem. thank you. Subscribing.

[gearheadek9]

first he working of the floor lol second he doing a bunch of cold weld loooool throw that ecu in ur car its probablity not even starting or stalling under vibration lol

[pacayabu]

@Sk8eRPR yo jamas habia visto que fueran tan estupidos los dos xd



[lidawgnz]

step number one, use a table .. lol jokes :P

[hondare85]

wow I now I know how to install the chip! u just need to go with the soldering iron to the little dots and then i dont know what u were doing and then melt the little things and then show my hand to teh camera for a long time most important of all dont say a word and thats it!