Trochoidal-Milling-316-Stainless-Steel.mov
Loading...
Loading...
17,134
Loading...
There is no Interactive Transcript.
Uploader Comments (frdikrll)
see all
All Comments (17)
-
The first trochoidal cutting was hand written and from what I understand took a long time to program.
-
What was the tool made of? HSS, Cobalt, Carbide?
What was the chip load?
What was the heat build up in the material?
I did not see any red in your chips might you have been able to have a higher spindle speed and a higher feed rate?
-
Part of the point of using this method is to keep tool lasting longer.
-
Use water to finish first
-
@frdikrll I was thinking the same thing.
-
@frdikrll ah right ok, its not needed for the materials i machine but i just wanted to have a play with it if it was possible to do like a short G code loop like helical interpolation can be done, but thanks anyway
Loading...
0:31
CNC Mill - how to break a toolby aloftindenver47,861 views- 0:28
Iscar ChatterFree Trochoidal Machining 316 SSby Iscarians8,936 views
- 0:38
trochoidal patternby bsihler8,998 views
- 1:39
Nutfräser / HPC / Trochoid in 1.7225by PokolmKnowHow11,654 views
- 4:16
Superturboby SecoToolsAB9,086 views
- 0:41
Helle Thorning nøgen på talerstol (hemmeligt klip)by p10trxs0hn7,473,284 views
- 2:08
heavy millingby bizdad20,850 views
- 0:40
ISCAR Groove Milling Application- MM GRITby iscarweb15,222 views
- 0:42
What not to do with your CNC.by eleehcsleoj284,434 views
- 0:27
CNC trochoidal milling-machiningby CADCAMexpert11,593 views
- 1:26
Tips film: Trochoidal milling machiningby sandvikcoromant15,037 views
- 2:56
Sandvik CoroMill 345 and CoroMill 316 Demo in Steelby coromantchicago18,339 views
- 0:47
Trochoidal milling/peel milling.With Iscar 12mm endmillby potifaren1,435 views
- 2:04
Mastercam Dynamic 2D High Speed on MX2by avongil3,085 views
- 4:21
High Speed Milling NC Programmingby mfgaainc35,189 views
- 1:42
Sandvik Coromant CoroMill 316 Exchangeable Head Millingby coromantchicago18,183 views
- 1:32
CoroMill® 327 and 328 for groove milling - Sandvik Coromantby SandvikCoromantUS8,674 views
- 0:31
ISCAR KNMX Insert-ruoghby iscarweb49,074 views
- 4:09
Inconel Milling With Ceramic Insertsby 78rozey19,654 views
just a question cus i cant find it anywhere on the net for some stupid reason, what would the G codeing look like for this Trochoidal Milling i am using a haas vf4 2010 by the way
rick371 6 months ago
ahhh... G-code mostly consists of arcs but it would be very hard to hand-write this type of toolpath - although not impossible. Usually it will take a CAM software - like MasterCAM, SurfCAM, FeatureCAM etc. to generate the toolpath/G-code for you. Because there are a lot of small moves to keep the chips thin it would take quite a lot of time to write all these moves without the help of some type of software.
...hope this gets you moving in the right direction.
frdikrll 6 months ago
I think u need a new end mill after this .
1966zaim 7 months ago
you should quit the thinking, only cut your fingernails and leave the metal cutting to professionals
- this tool cut 32 parts.
frdikrll 6 months ago
Hi Alan
It works on pocket, boss and side features. Go to the milling TAB, click on "curly corner" (on the right), check "enable" and start with a small number (.030") or so for corner radius, then play around with the numbers and simulate the toolpath to see the differences. If you mill a slot the tool diameter plus 2*corner radius must be smaller than the slot for the tool to fit.
...later
F.
frdikrll 2 years ago