06 - Magnet motor bobbin assembly progress.
Loading...
Loading...
65,162
Link to this comment:
Share to:
Uploader Comments (ZeroFossilFuel)
Top Comments
-
Even though you have fabricated a racing track for a bearing to help move the lever up and down at the precise time, would mounting the half shaped magnet on a spining disk with perhaps two or three more hard drive magnets (to keep the 2:1 ratio level you have currently) instead of needing a lever action?
4 years ago 3
-
hi , could you not put a larger diametre tube over the bobbin and mark the raceway you require on it then remove it and cut out the raceway and then slide back overand stick it to the bobbin, then you would have no need for the tricky wire raceway , only a sudjestion and think your doing well , fitz
Loading...
- 4:20#299 Cleanup after Snow Storm Albertby ZeroFossilFuel4,166 views
- 10:22#298 Remembering Snow Storm Albert and CL&P poo...by ZeroFossilFuel1,244 views
- 11:16#297 Muller Motor Generator Rotorby ZeroFossilFuel6,325 views
- 4:27#296 Muller update, 2nd build startingby ZeroFossilFuel2,800 views
- 3:00VAWT : Build a Mag-Lev VAWT wind turbine from c...by tiantan63142,836 views
- 1:28Magnetic Shielding Demonstration #3 Autono-Driv...by MagnetOnlyMotors60,874 views
- 6:58Green Motor Project Video 1 Truth About The Per...by magnetmotortv327,356 views
- 1:48Perpetual Motion and Nikola Tesla (Tapping Infi...by debunkified245,245 views
- 8:1805 - Ideas needed for bobbin assemblyby ZeroFossilFuel12,875 views
- 0:16UT Arlington Pulsed Detonation Engine 25 Hz Gro...by emb894,905 views
- 4:54Homopolar Motor With Five Speed Manual Stick-Shiftby MrfixitRick776,353 views
- 3:38Magnet motor, energy boostby Roobert337,956 views
- 2:52Hartmann Magnetic Motorby Eltimple101,346 views
- 4:46Permanent Magnetic Motor from Argentina. A self...by 77GSlinger186,094 views
- 7:01SKYSHIP MOTOR, FANTASTIC EXPERIMENT....!by skycollection94,340 views
- 9:35Perendev And Bedini Magnetic Motorsby SowhatNC870,512 views
- 8:5601 - Steorn concept Permanent Magnet Motor testby ZeroFossilFuel851,407 views
- 0:21Magnetic Motorby strombom279,760 views
- 4:41Magnet Motor flywheel/generator1by mcorrade69,458 views
It could be a continuous weel that could be rigged with a pully system or belt? I am not sure if that even makes sense but if it does please respond. Other than that, great video, very helpful. - The House
House66 4 years ago
My next prototype will be almost exactly that, just not with the HD magnets and a 4:1 ratio minimum.
ZeroFossilFuel 4 years ago
Great, you are a rare one who is trying to close the loop and is not afraid of showing your results. Success or failure its fun anyway.
I think you need something like a cam. This wire thing is too fragile. I'll do an animation and post for you.
OmegaThe1 4 years ago
Cool.
ZeroFossilFuel 4 years ago
You'll may be needing some kind of emergency stop mechanism because, who knows maybe it will accelerate and accelerate until it will brake apart :D. Just kidding. I will wait for the test run.
I3ursucu 4 years ago
Got one. It's called my hand. ;-)
Seriously though, if that does happen, and I hope it will, the flimsy bearing raceway will probably break first stalling the motor before causing me bodily injury, but not before catching the event on video.
ZeroFossilFuel 4 years ago