How to: Advance timing 1/8" on your 89-93 Dodge cummins VE pump!! more power and +2mpg! best mod

Video showing how to advance timing "1/8" on yiur 89-93 Dodge cummins VE pump.

Also works on 4bt cummins engines with VE pump! one of the best mods out there. Increases mid-top end power on your cummins.. in some cases your spool up time will suffer but that depends on pump tuning. do all 3 mods in my videos and your truck will get up way faster and you'll have a smile from ear to ear.

www.dieseltruckresource.com
www.1stgen.org

Crossy's son

Category:

Autos & Vehicles

Tags:

• dodge
• cummins
• turbo
• diesel
• ram
• 2500
• 250
• w250
• w350
• 89
• 90
• 91
• 92
• 93
• smoke
• video
• 0-60
• how
• to
• get
• more
• power
• VE
• pump
• timing
• advance
• slow
• faster
• torque
• duramax
• powerstroke
• 5.9
• 6.4
• 6.0
• 7.3
• 6.6
• startup
• cold
• start

[TheMrAMack]

How long did this mod take you? This is the only mod from your videos other than the 3200 governor install that I haven't done to my old cummins, and I think I'm going to give it a shot.

[91CTD]

@TheMrAMack Takes me like 20 minutes now .....hour then. you do need a 13mm S-wrench to get the very bottom pump bolt it's a pain

[416rm]

Great videos, I appreciate them. Does any of the pump mods sacrifice pump life at all? I had 224,000 miles on the stock ve pump before it finally died. Smokey mess when it finally quit.

I'm thinking seriously about a new M&H fuel pin along with your recommendations on the pump screws. So far all i've done is a 4'' diamond eye exhaust and 40hp Lucas Injectors.

Thanks

[91CTD]

@416rm Nah the pump will bef ine. M&H makes a good pin. Sounds like with POD injectors you're gonna have alot of fuel. be sure to have at least boost and EGT gauge, EGT Pyro mounted pre-turbo.

[CR125killer]

yeah this after a while will mess ur the pump two of my friends pumps kept messing up and thats y it will help a little but its not worth it in the long run just saying the pumps are about a $1000 +or- $100 depending on where you get it

[91CTD]

@CR125killer It doesn't have anything to do with the pump itself so It can't mess it up. Don't mislead people.

You are changing when the injection event happens, doesn't change ANYTHING to do with the injection pump.

[TheMrAMack]

@91CTD :Thanks for the info! I'm gonna give it a shot over my spring break. Ill try to post some videos of my old truck too.

[chrisreh]

i have a 1992 dodge cummins and i just checked the 2 slits,one is on the timming cover but there is not one on the pump.how can i make the right measurement if there isnt a line?

[47927411D]

Good Job !

[91CTD]

@Black80Z Someone could have already advanced it

When these things are really stock alot of timing only hurts the bottom end performance...plus you have a 21cm exhaust housing because it's a 92...It's easy to tell theres a "21" cast into the BACK of the exhaust housing , like right above where the exhaust pipe goes into the turbo. you'll have to get a flashlight and get up in the engine bay.

This combo will make SPOOL UP horrible....Get a HX35 turbo with a 12cm housing off a 94-98 truck.