Screen Printing - Taping Newman Roller Frames
Loading...
Loading...
6:28
Screenprinting - Perfect Prints Every Timeby billhoodconsulting7,525 views- 5:09
Pt. 1 - Frame Assembly Newman Roller Frame with 4 Rollersby NewmanRollerFrame980 views
- 1:03
Ryan Screen Printing Supplies: Taping a Frameby RyanSPS1,995 views
- 7:37
T Biz Screen Making Part Three - Basics of Exposure & Washoutby TBizNetwork17,652 views
- 9:02
Using the Newman Roller Master - Part 2by NewmanRollerFrame894 views
- 7:12
Exposing a Screen for Screen Printing, Screen Exposure Problems PART 1by Ryonet63,621 views
- 6:17
Pt. 2 - Frame Assembly Newman Roller Frame with 4 Rollers.by NewmanRollerFrame1,040 views
- 6:02
Newman L.O.C. Gauge (LEVEL and OFF-CONTACT GAUGE)by NewmanRollerFrame892 views
- 3:13
Screen Printing: How to Tape a Screenby atlasscreensupply1,155 views
- 5:33
Panel Frame Eco Friendly Screen Printing Framesby jdoggenator10,608 views
- 3:36
Monkey in a Dryer on Red Eyeby MonkeyInADryer610 views
- 1:02
Newman Rollermaster M3 - Quick Videoby NewmanRollerFrame811 views
- 2:24
T-Shirt Printing - Homemade Screen Stretchingby kurniawandennis211,410 views
- 0:32
Tape your squeegees by Vastex Internationalby VastexInternational4,949 views
- 6:38
The Tape Trick on a Vastex V-1000 manual screen press.by VastexInternational9,406 views
- 4:28
Apply Screen Printing Capillary film w/ the Roller Methodby thegrendelvideos12,321 views
- 2:02
Screen Printing: How to Coat a Screen with Emulsionby atlasscreensupply9,919 views
- 8:06
Screen Printing's Best Screen 2by rogerjennings11,822 views
- 10:40
Newman Roller Frame's NEW FlashPanels Screen Printing Meshby Ryonet5,201 views
- 1:44
All Heads down on a Vastex V-2000 printing pressby VastexInternational46,637 views
@inkstains1 - You do not want to put a blow dryer anywhere near your mesh as it will cause the mesh to lose tension and worse, it will occur at different levels.
If the tape is applied on both sides of the mesh and aligned correctly, the glue moves through the mesh openings and creates a chemical bond with the two strips of tapes. When the water pressure is applied from either side it would only push the tape into the mesh, not away from it.
billhoodconsulting 1 year ago
Some of our screens the tape didn't hold together. The tape stuck to the metal, were they meet on the mesh they seperate under water pressure. I'm not sure why. Is there somehting that we can do to make stick better? Like say a blow dyer or a glue?
inkstains1 1 year ago
Yes, you can adjust the tension. The tape at the corners is meant to be pulled back slightly so that the wrench can be placed on the end plug. I don't remove the tape until it reaches a serious point of degrading. This can sometimes be years after I apply it. Most of the larger print shops are using this technique. I can assure you that those shops exposing 1200 screens a day are not taping every screen. ;-)
billhoodconsulting 2 years ago
So, can you adjust the tension still? How do you remove the tape when needed?
DaJackal05 2 years ago