How to FULLY bridge any amplifier! EASY steps
Loading...
Uploader Comments (barevids)
All Comments (95)
-
Hello. I got 6 Speakers whit like 400-500W each, And i put them into a Denon 1991 Amplifier whit 50W x2.. But one day something happened so that only the "Right" side put out any power.. Any idea what could have happened? - Sorry for my English - :)
-
@barevids could I do this with audacity? I can do the inverting part with audacity but how do I know which positive is negative and which positive is positive? I have a SIMPLE amplfier with no gadgets. just left and right channel wires. do I just invert the right channel in audacity? and hook up both positives to my sub and thats it?
-
please can you upload some more vids on your surround sound tline recent video's please cheers!
-
@PA3555 DONT* sorry error x)
-
fuck off i want destroy my yamaha rx-v371 >..< i have 100wx5 or in stereo mode switch in 250 W x2 il love this spec :D
-
@barevids but i have speakers with subs built in and i want there full potential
6:46
Bridging amplifiers - basics of bridging a non-bridgeable ampby barevids26,888 views- 4:52
How bridgeable amplifiers work! Bridge / Parallel Mono ~ EXPLANATIONby barevids17,510 views
- 4:14
Three 12"s, two 10"s and four 8"s - Clips not seen beforeby barevids2,575 views
- 4:58
x2 Pioneer TS-W121SPL! Drop it drop it low!by barevids127,475 views
- 6:05
How to bridge a 2 channel amplifier.by bassabigdeal13,168 views
- 6:53
Car amp set up in houseby demonsparkx21,954 views
- 0:41
1400 watts pioneer subwooferby siddiqiarsalan208,516 views
- 2:13
My Ride at 146 dB !!!!!by lowbassmakker84,356 views
- 4:36
MIM PA System Instructional Videoby toez1056,389 views
- 0:52
Ohms and Wattsby dalewestae55,879 views
- 3:04
How to wire 2 DVC 4ohm subwoofers bridged 2 ch. amp. Watch in HD!by mazda228412,801 views
- 2:14
kicker 18" solo xby KickerPimp114,453 views
- 0:10
CAR AUDIO SETUP IN HOMEby esjayay145,081 views
- 1:18
Mega Bass Testby splisser12005,560,117 views
- 1:10
Elevation Audio Exe 15by PBL9071,051,925 views
- 0:51
My handmade power amplifier project 1000Wby toniemi85195,040 views
- 2:49
Logitech z906 z-5500 z-2300 2by 999darek116,864 views
- 1:52
Crown International XLS Series DriveCore Power Amplifiersby MarkertekVideoSupply22,029 views
- 2:20
Re: Re: What does bridge on an amplifier meanby Chrls514,942 views
I am a beginner, Can I connect 4 speakers each 500 watt to a 3000 watt behringer amplifier? Is there anything wrong? Do I need more than 2 amplifier If I have 10-14 speakers for club, How do they connect speakers in the club? Please answer!
SuperErin21 4 weeks ago
@SuperErin21 I have replied via messages at its too long to write here.
barevids 4 weeks ago
my technics is onyl 8 ohms stable but i can run it full power at 4 ohms no problem irt handles it like a beast iv ru 2 ohms before but it goes into protect maby i can try this and my amp will be happy
BassPounderX 1 month ago
@BassPounderX if you bridge your amp in this way you should only run an 8ohm speaker. If you run it at 4 ohms bridged each channel actually sees 2ohm so it will go into protect
barevids 1 month ago
i have that top amp (the silver sony) but when i use mine i does not put bass out of the speaker channels it does not work! bass only comes out of the subwoofer output. HOW DO I FIX IT?
DMIsREAL 2 months ago
@DMIsREAL bass does come out of the other channels, but the amp isnt very bass sensitive. go to 'tone' on the menu and make bass +6. thats about all you can do... it just doesnt give out a lot of bass to the front center and rear speakers. Thats actually how you want it to be, the bass gets sent to the subwoofer channel.
barevids 2 months ago