Fixing a mini lathe on Madmodders site
Loading...
Uploader Comments (blogwitch)
All Comments (7)
-
did the same on my new one, now its very good.
patrick
-
Thanks for replying, I figured finding the hole center from edge when I saw the measurements of the parallel, the bolt and the total measurement of the parallel and bolt and came up with the same solution as you did (before looking at your answer, of course). again, thanks.
-
I know this might be a bit late but I read your thread on madmodder, on "fixing Darren's lathe" and found it very enthralling, captivating that I followed it to the end and then found the article "MACHINING IS ONLY A STATE OF MIND." an enlightening read, and true to its word so I hope you don't mind me posting it as a mantra in my shop, as a reminder: there are other ways of doing it other than not doing with what you have.
-
Thx... sent my reg request. So I guess I'll see you there. BTW, you can post links just put them in as you would your normal comments, they are allowed as long as they don't link to anything that's not allowed.
-
Ooh, that's nice.
-
Looks like a worthwhile fix but could not find the site. Any chance of placing a link here? Thanks
3:57
Peck drill (very small holes on the lathe)by Dividedhead153,749 views- 2:07
Micro Mini Metal Latheby kbidtv02113,315 views
- 2:15
Boeshield 3-Part Tool Care Kit Reviewby thintz125,321 views
- 0:20
lathe issue?by outfitter19538,829 views
- 5:55
Demonstrating the Dream Cutterby manovermetal125,329 views
- 0:50
How to Make a Home Made Mini Lathe/sanderby Molotov194364,868 views
- 1:44
Turning stainless steel on the Micro-Mark 7x14 mini lathe...by myshots1018,749 views
- 0:48
How to Use a Fly Cutter with the Micro-Mark MicroLux Mini Milling Machineby micromarktools113,021 views
- 9:18
mini lathe on aluminiumby Martrix6419,821 views
- 97 videosTIRE FITTING
- 10:00
Scraping in a lathe's top slide (with tapered gib)by MuellerNick15,450 views
- 7:59
screw cutting project part 2by oakphisto22,621 views
- 7:48
Part 2 Making a slimline pen on a Clark mini latheby headbangeruk9,499 views
- 1:56
Lathe tool sharpening made easyby richieT73798,374 views
- 1:33
7X14 CNC Mini Lathe - Inverse Taper Turningby rriosq6,329 views
- 0:27
Watchmaker lathe with Millingby FranciscoAparisi39,762 views
- 3:06
Metal Lathe Mod For Precision Cutting/Turningby richieT73712,798 views
- 9:58
Basic Lathe - Operation Threadingby GeorgeandJeri46,146 views
- 2:44
The Powerful JET® JWL-1220 Mini Latheby JETTOOLSUSA54,488 views
- 1:03
SEIG 7X10, 7X12 CNC MINI LATHE KIT1.MOVby CNCTAIG20103,471 views
- 0:25
7X14 CNC Mini Lathe Taper Turningby rriosq4,979 views
in "fixing Darren's lathe" thread on madmodder's, you were measuring hole location to fit the angled gib (page 3, 8th post) you used magnetic paralells to measure datum face to first [bolt] hole: was this to find the center of the hole from the edge? did you have to divide the size of the parallel and the dia. of the bolt to get center distance from edge? I have a similar lathe and am trying to do the same.
togaida 2 years ago
Togaida,
Anything of mine that you find on the site, please use as you see fit.
With regards to the parallel. To find the centre of the hole, I subtracted the full width of the parallel plus half the width of the bolt from the overall reading to arrive at the centre position of the hole from the metal's edge.
Hope this helps you in some way.
blogwitch 2 years ago
Normally utube doesn't allow links, but if you put either a search in or type this into your url link at the top of the page, it should take you straight to the site
madmodder[dot]net
Replace the [dot] with a full stop
blogwitch 3 years ago