how to lift a tsop from a cable modem
Loading...
Loading...
2:00
FREE Internet TV: A How To (Cancel CableTV)by paul7986495,556 views- 0:23
TSOPby xb0xisbetter60,785 views
- 3:33
how to connect rs232 on a cable modem http://www.thecablemodembible.co.cc/by gggggranty47,971 views
- 0:27
Installing a Solderless Pin Header on a SB5100by docsismodem17,372 views
- 7:49
Dec 5th--DOCSIS 3.0 MODEM---Motorola Surf Board 6120by kirktaylor201028,140 views
- 3:20
Professional SMT Soldering: Hand Soldering Techniques - Surface Mountby jkgamm041209,761 views
- 7:17
como Flashear un cablemodem sb5100 - 2parteby k4d4v3r518,492 views
- 5:01
Xbox mod and/or hackby GeneralMatt1109,441 views
- 1:31
How to Build a Cable TV Descramblerby mrshow555886,908 views
- 2:56
TSOP32 Installation Drag Method | BEST, Inc.by SolderingGeek23,351 views
- 1:01
Connecting an ADSL broadband routerby zentechvids317,310 views
- 4:24
Lingo Digital Phone Quick Setup (w/Router&DSL/Cable Modem)by AndrewXPS20089,252 views
- 2:12
webstar 2100 hackby freeneo216,037 views
- 4:33
sb5100 como hackear y hacer el debrick usando usbjtag NT (Debrick using usbjtag NT)by bertopinol4,565 views
- 1:36
cable tv hackby watog2172,527 views
- 10:01
The Wankers Who Own the House I Used to Live Inby ElleRigby12,590 views
- 4:06
tftpd32howtoby DeathsTouch25,135 views
- 0:26
Arris Modemby Shaipnoypogi14,042 views
- 4:56
Uncapped cable modem 0/0 fastby jtsnowboy12343,425 views
- 0:29
Ambit VMNG 300by gggggranty4,217 views
Can you re-flash the same Lifted TSOP with the original bootloader? also how would i go about doing so. thanks
DemonsPride 11 months ago
wheres flux?
mjurzak 1 year ago
o hai! u uploaded our old video :D made this when was working with engel to show him how easy it was, at the time he was sending modem's to europe to get flash chips replaced...
Pointless trivia: Used old old ikegami 3 tube broadcast camera, U-Matic vtr, and a blinding 1000W halogen lamp off to the side. Input'd using ATI allinblunder.. borrowed frenz 300mhz imac and an obtained ( >_>) copy of finalcut for editing. Originally had Boards o Canada as the soundtrx but engel changed it ( u_u);/
ForbiddenMagic 3 years ago
what chip do you replace it with an where can i get loads? many thanks, good visual education for the deviuos mind.
kr00418948 3 years ago
like jiggaman said....."what is this for" ?
(my guess it gives you internet access for free) As long as they havnt turned it off by the green box outside :)
biddy79uk 3 years ago
like jiggaman said....."what is this for" ?
(my guess it gives you internet access for free) As long as they havnt turned it off by the green box outside :)
biddy79uk 3 years ago
Hot air gun and stanley knife is much much easier i think anyway, but have done it this was too but only once.
PaulsPoker 3 years ago
add more solder to the bridged area m8, then flux , then heat- then put solder wick close and heat solder with flux it should always run strainght to wick - theres always a stuborn bit! always pull wick away 1st before the iron as u might already have out!! how tracks r usually damaged... i did on my first 1..hope all goes well for u though - not every1 has old boards to prastice on like i had - but try n find old circuits that may have tsops or similar chips to practice on!!!
scottyskunkman 3 years ago
cheerz man, i used this vid only and on my second attempt it was dare i say near on perfect i had 2 old 120 abits lying around soo i used these to practice on b4 i set to work on the 250/255s i had..patience common sense and a basic soldering skill already is beneficial...i used a £5 iron with cinicak shaped end like u cheap solder flux and wick i think the secrets in the flux-well it was with me!! cheerz again m8 very handy indeed...
scottyskunkman 3 years ago
whats this for?
jiggaman17 3 years ago