Mold Making Silicone appliance Part 2
Loading...
Loading...
16,029
Loading...
Link to this comment:
Share to:
Uploader Comments (brickintheyard)
see all
All Comments (19)
-
@GThe0dd0ne0ut If you are very careful removing them. I find it is cheaper just to recast them. This appliance only cost about .75 cents.
-
@brickintheyard Thanks so much!
Sorry if I spammed you!
-
@brickintheyard Thanks so much!
Sorry if I spammed you!
-
@brickintheyard Thanks so much!
Sorry if I spammed you!
-
@brickintheyard Thanks so much!
Sorry if I spammed you!
-
lol, "backside mould"
Loading...
- 7:16
Mold Making Tip: Silicone Appliance Part 1by brickintheyard13,173 views
- 9:25
Mold Making: Platsil Gel-10 Lifecastby brickintheyard75,748 views
- 6:54
Mold Making and Casting: Silicone Face Part 1by brickintheyard137,482 views
- 9:25
Mold Making Technique: 1 piece mold with Gel-10by brickintheyard16,280 views
- 9:55
How to make Gelatin Special Effects appliancesby Boosels57,839 views
- 4:51
How to make a two-part moldby tapplastics846,791 views
- 3:31
Mr. Trump's 757by trump1,173,138 views
- 2:10
SILICON-MASK 02by christiancocco35,069 views
- 6:44
No Budget Mold Making for face appliancesby silvermetalflake9,142 views
- 6:15
How to Make a Silicone Ring Mouldby spinella1981186,090 views
- 5:26
How to make a simple Silicone Mold Part 1by tapplastics283,216 views
- 0:51
Making Silicon Molds for Pewterby DeanLeatherman10,706 views
- 4:08
Life Casting: How to Make a Mold of Your Face with Alginateby SmoothOnInc166,690 views
- 0:35
Creating Character Prosthetics in Silicone Pt2by skeeterpig54,309 views
- 7:04
Updated - Simple Silicone Rubber Molds (no parting line)by freemanmfg106,982 views
- 1:46
Vacuum bag laminating table to make flat parts Part 1by lesburn13,727 views
- 5:39
How to make a simple Silicone Mold Part 2by tapplastics179,160 views
- 0:51
Reusable Mold Making Material, Making parts without the cost.by ComposiMold18,487 views
- 1:53
Torchwood - Neill Gorton Interview: Creating Corpsesby HereComeTheDrums3,378 views
- 1:03
Creating Character Prosthetics in Silicone Pt3by skeeterpig18,452 views
When uniting a two-piece mold, I heard that one must create "channels" to allow excess casting material to escape, thus creating a better casting. It doesn't appear that you do this--any thoughts?
creepsomber 1 year ago
@creepsomber I did create an overflow area but in this case it was very crude. This is a very simple mold for small appliances.
brickintheyard 1 year ago
I'm so sorry if you get this comment several times--it doesn't appear to be working!
Great videos! I've spent hours watching them and picked up several hints. What ratio do you use of water to Murphy's?
PS--any videos around of making acrylic nails? I can't get mine clear
megandmax 1 year ago
Comments are approved 1st to reduce spam. Murphy's 1 part - water 3-5 parts.
brickintheyard 1 year ago