GENERATOR 12 DC VOLTS IN --237 DC VOLTS OUT

This is a redesigned generator. The shaft contact bearings are a STEEL ACORN NUT and a SPHERE MAGNET on each side of the magnet axle. Supporting the axle is two huge stacked rod magnets inside aluminum housings. Those are at each end of the axle shaft. Red tape marks North polarity and Blue tape marks south polarity. POLARITYS MUST BE OBSERVED or this wont work.The white tape is to keep the magnet tube from slipping inside the clamps holding it. The "DIAMETRIC" ring magnet is free to slip on the shaft and the shaft is free to slip inside the magnet and turn on its own.

I put shaft collars and nylon washers in place to center the magnet only and keep it from sliding around left or right on the shaft. They acually are not needed if the spinning magnet stays in one spot. ---- It wont. ----

Things keeps getting better! I just made another modifucation and now the magnet shaft has much more torque. Definetely more speed. I am up to a DC OUTPUT of 280 volts Using an INPUT of 12 volts at .08 amps. Thats with the magnet spinning and the full wave bridge rectifier putting out the 280 DC VOLTAGE. My INPUT is .96 WATTS and holds steady. I am going to run a actual POWER OUT test tomorrow and will post that video along with results. From what I see so far if I can better the 1 watt input power it takes to spin the magnet this device will go overunity.
I need to buy certain value resistors and use them in series with the generator output and a multimeter. I will see if I can draw more than a watt out. Below is the online calculator I am using to be sure I am not messing up my calculations.

http://www.sengpielaudio.com/calculator-ohm.htm

My intent is to reach a point in development where I might see overunity occur. More out put power than input

Note:.Patent pending only on Magnets/Axle/Flux coil setup.
Commercial interests contact me. Individual replications ok.

Category:

Science & Technology

Tags:

• ELECTRONICS
• MAGNETICS
• WIERD
• GENERATOR

[hrford]

The output waveform will have tons of harmonics on it. Are you measuring power factor as wattage only works with DC and pure AC sine waves?

[64298]

@hrford Dont have the notes any more. I have moved on to something a lot more interesting. If It works I will have made the first GRAVITY ASSISTED all permanent magnet motor using only 2 magnets. NO ELECTRONICS WHATSOEVER. Plently of motor power speed and torque. from a small model. Check my newest updates on my most recent video which is also history right now. I will have a new video on You Tube within a week.

[khoiktran]

what amps is that generator pushing?

[64298]

@khoiktran Not much from what I can recall. i am out of this now and working on a SMOT motor device. Check out my last 2 videos. I am way beyond even that now. Read the updates in my last video. Thanks

[64298]

@rostit420  I have moved on . Check my latest video.

[rostit420]

@64298 What are your Amperage measurements? What is the output frequency? You build a nice machine, but I would have to see actual test data. You cannot create energy. Only change its form and with friction just from air, you are losing efficiency. Please use your skills to achieve the possible.

[querdenker79]

This is NOT moor power, this is a transformer.See my video.

Das ist eine Blindspannung -Back EMF spikes.Schließ einfach eine 50Watt lampe an und sie wird nicht leuchten.

[64298]

@querdenker79

I am aware of this. When you multiply the input voltage x current you get watt power. Now if you do the same with the output and find your wattage is higher then you have gone overunity.

This video was taken a long time ago and I am way beyond that now.

Check my latest video TEST TUBE GENERATOR. My output is greater than my input and I have an organization already interested and developing it further. Still open for an offer for the original setup.

[querdenker79]

This is NOT moor output...238V DC is the Back EMF spike.A simply pulsmotor-transformer...NOT generator.Wrong turn for Over Unity:-)

[64298]

@kurisu925 I have not seen better yet by anyone. Anyone claiming an overunity device basically has a monetary/fame reward in mind. If its a for real thing he would post all details as to how to make it and let the world in on his invention. Recognition and what ever fame, money, glory, ect. follows would be his alone. When someone asks to crack your wallet to get an insite as to what they have to offer -- Beware.