3x3 FLA CNC Maiden Cut
Loading...
Uploader Comments (CrashHancock)
All Comments (9)
-
geat thanks, i have been looking for confirmation about your exact driver setup because i went with gecko g540 and the 48v 7.3amp PS & 425oz all from keling as well and i was worried i was going to lose my rapid speeds, the machine im going to use it on is rack and pinion and is very quick, so thanks again.
-
what size motors are you running? 425oz? i have been following these guys for some time, is the kit fairly stress free to build? any difficulties assembling? also how man IPM are you routing in the vid? looked great!
-
nice work man, im waitin on my kit from fine line auto right now. cant wait
-
Crash, that machine looks great! But your vacuum is a LOT louder than the router motor. ;-)
I'll bet you'll soon be running it at 250 IPM between cuts. Woohoo!
-
Lucky !
6:52
How NOT To Dispose Of A Lipoby CrashHancock3,516 views- 0:41
FLA300 4X4 R&P 8020 First Movesby brrimmer5,064 views
- 0:19
Lathe Machine Crashby jtmovies199360,895 views
- 3:08
Crash Course in Milling: Chapter 1 - Basic Machine Anatomy, by Glacern Machine Toolsby GlacernMachineTools166,232 views
- 0:14
Precision Plasma 2000ipm.MPGby elvis16694,902 views
- 6:17
Cutting Curved Aluminum Plate on ShopBot CNCby ShuttleSpaceCA29,533 views
- 6:31
Fine Line Automation FLA-100 Build Part 2by gemrough7,487 views
- 1:20
DIY CNC Gecko G540 Bench Testby PauloInTexas2,023 views
- 1:00
Big CNC milling machine - homemade and built on a budget!by baileybots3,922 views
- 2:41
#1 CNC Mill Build FLA100. Inspecting the machine, where to from hereby xtcncvids1,352 views
- 0:28
Arduino Controlled XY T-Slot Tableby TeleToyland26,823 views
- 0:37
FLA-100 Clone: Moving The X-Axis With A Drillby jbeuckm669 views
- 0:29
CNC Router Parts Extended Linear Carriageby cncrouterparts5,202 views
- 0:42
CNC Wire Cutting Machineby mughalks13,543 views
- 0:31
rc helicopter crashby TheZander972,429 views
- 1:04
CNC-Crash an einer Fräsmaschineby 234454170,222 views
- 1:20
Roughing Aluminum At 1100 IPMby Slapstick12312310,063 views
- 4:44
CNC routing aluminium crash box by dtbs.netby darrelturner32,736 views
- 2:16
Belt CP with CNC tail 2 crashes same flightby lanex29826 views
NVM i asked the IPM before i saw the ending lol oppsie but what about the motors?
irishkendoll 1 month ago
@irishkendoll Yes, those motors are Kehling 425 oz, NEMA 23 steppers. This machine is capable of rapids to 300 IPM, but I usually run about 100 ipm these days with the actual cutting feeds as fast as the bit and material will allow.
CrashHancock 1 month ago
motors are way bigger than your power supply specs, and of course for the beauty of G540. the G540 works with 50V so the closer you are, the better you get. greatmachine anyway!
warjol 2 years ago
I am running a 48 volt power supply with 7.3 amps of current. That power supply was recommended to me by the folks I got the steppers and 540 driver from (KelingInc.) Everything works nice and strong - fast too!
CrashHancock 2 years ago