waste oil burner no preheat and veggie oil only
Loading...
Uploader Comments (shayneyasinski)
All Comments (10)
-
Nice and powerful flame. I'm going to build one and I have a question. From what I can see the nozzle arrangment is soldered I think. Doesn't it get too hot so that the solder could melt eventually ? I also want to solder a drilled cap on a copper tube but I' m hesitant to do so for this reason.
Thanks.
-
hello
what is the oil consumption????????
-
Good setup.
If I were to do a babbington style I would do it the same way. Don't see the need for a ball with this style of atomisation. Small hole into a stream of oil will work fine.... as you have well Shown!! :0)
-
preheat is not needed, atomizing has a very high efficiency! Good Job! :)
-
how did you not have to preheat
-
is that a small babington, injector nozel, or drip into injected are type?
0:38
Waste Oil Burner Test Runby flanxnpip3,028 views- 0:21
Waste Oil Heaterby ddchopper162,031 views
- 1:07
Waste Oil Burnerby nowudmsain5,908 views
- 1:45
Simple waste oil burner 3by richiewrench35,104 views
- 2:09
Siphon Nozzle, Waste oil Burner Test 1by LandsharkLabs12,211 views
- 1:19
Babington Version 1 with Flame Tube Cappedby OilBurner2008122,917 views
- 1:04
Babington Water Heaterby MrMbirrell23,368 views
- 1:49
Waste oil burner heaterby wiatroda141,792 views
- 7:29
Babington Waste Oil Heater Instructionsby ddchopper18,654 views
- 1:01
Babington waste oil burnerby DimensionMachine63,445 views
- 1:10
home made waste oil burner heaterby porschestyling25,477 views
- 0:46
Mother Earth News waste oil heaterby yonmoore23,667 views
- 3:14
Waste Oil Heaterby SuperSimpsonz23,558 views
- 1:46
Burner for waste engine oilby LightningAlan89,630 views
- 0:30
Babington ball flare nut 1st try.AVIby TheEquineFencer12,733 views
- 3:33
Waste Oil Burnerby Hubilizer2085,952 views
- 2:17
Waste Oil Heater Test 2by txpilot8212,160 views
- 2:11
Homemade Babington Ball Waste Oil Burner Boiler Furnace - Part 1by jpmcnam27,932 views
- 0:56
Oil burner Detailby billygotgrove76,228 views
- 1:18
Used Engine Oil Burnerby kiwiavi10,818 views
depends on how big a flame you want, I burnt a gallon in as short as 10 min or as long as an hour
shayneyasinski 2 months ago
The ball is the best way to eliminate plugging up, With the ball all you need is a good pump to circulate the oil.
shayneyasinski 6 months ago
The oil burns well as soon as it hits the tube, pre heat would help I am sure but it was not needed for this used deep fryer veg oil.
shayneyasinski 8 months ago
just a very simple drip oil over a tiny hole, not all that good IMO.
I bought a bab ball and will be building a new setup soon.
the ball is the way to go as you can then use a simple pump that can pump oil over the ball and the flow can be alot and you will have no chance of plugging.
shayneyasinski 1 year ago