004 Improve HHO test housing & TEST Figures!

yea I added some stuff to help in testing my cell.

I also recommend a couple of products, but as with anything else, shop around and try to get the best deal.

Great White Pipe Joint compound = great for connections; rated at 3,000 psi on gases from -50 degrees F to +500 degrees F; here is the link for the specs/info only (IOW I'm not making money by posting these links)...

http://www.lowes.com/lowes/lkn?action=productDetail&productId=23538-138-3...

Roebic Crystal Drain Opener = 100% Sodium Hydroxide! Here is the link for it...

http://www.roebic.com/catalog/clog.htm


I also did some initial tests with the Sodium Hydroxide and my Smack Booster cell. Note: I used 2 liters of water and added the Sodium Hydroxide by the teaspoon.

1. Cold cell, 1 tsp, 10.95 V, 15 amps, 500ml = mmw 3.04

2. cold cell 1 tsp, 12.6 V, 22 amps, 500ml = mmw 2.58

3. lukewarm cell 2 tsp, 9.98 V, 24 amps, 500ml = mmw 2.51

4. warm cell 3 tsp, 10.35 V, 25 amps, 500ml = mmw 3.74

Anyway, thats what I have done so far.


AH



p.s dumb question but what am I shooting for when it comes to MMW? What is everyone else getting? Drop a line and let me know.

Category:

Howto & Style

Tags:

• AlmostHydrogen
• HHO
• stanley
• meyer
• fuel
• cell
• booster
• electrolysis
• browns
• gas
• water
• car

[mowerman54]

steve; I have built a 16 plate booster as per electriks plans, have seen by adding 2 more plates, would decrease my needed amp, hopefully. I am using KOH as a electrolite, but am having some problems. Am running about 15 to 20 amps, but my problem is that the electrolite seems to foam up when running and then feeds into my bubbler. This happens after running only 10 mins. what am I doing wrong. I got a vid of my unit to give you an look at my system. Thanks

[AlmostHydrogen]

wow pretty nice setup with your buggy. Good job.

As for the foam, it looks like you have too much water in your cell. Your water level should be about an inch or two above the top of your plates. I use 2 liters of water (with NaOH) and the foam problem went away.

Keep up the good work - it looks like your going to have fun testing your buggy.

AH

[toyotech1974]

Steve thank you for all the information about hydrogen, you the man bro, if you need anything send me a e-mail, i'm a toyota tech if you ever need any electrical inf let me know

[AlmostHydrogen]

wow thanks for the offer, i might have to take you up on that when I start trying to install it in my truck (cause I am clueless about all that).

thanks again.

AH

[kpo86]

did it leak at the bottom

[AlmostHydrogen]

Once it was sealed with Great White Joint Pipe Compound, and tightened up... it did not leak.

:D

[ExplodingTeeth]

Try the F-16 Pulse King with your HHo Unit

You can Buy it on Ebay, What a difference it made in driving.

[Spicygarden]

Dear Mr. steve,

I would like to ask the brand of pipe joint compund w/ teflon that u show us, because i cant see the clear that brand, thank you

Willy, Jakarta, Indonesia

[flipster12000]

You mentioned a possible chemical burn associated with sodium hydroxide. What you say there is very correct. The best way to neutralize the alkaline is with an acid. DON'T USE SOAP! Use distilled white vinegar. Then rinse hands thoroughly with just water, after they are dry, then wash the vinegar smell off with soap and water. It is always a good thing to think safety first. Keep up the great work.

[AlmostHydrogen]

Well the majority of cells I see on yt are like the Smack Booster - gotta start somewhere. I do plan on making & testing other cells.

Thanks for stopping by and I will check out your vids.