Jointers - Setting & Using
Loading...
Link to this comment:
Uploader Comments (InTheWorkshop)
Top Comments
-
After watching many many of Charles' videos the only thing that comes up my mind is that he is the best old school, yet modern woodworker I've ever seen.
Simple, on topic and entertaining.
Bravo! I love these vids...
3 years ago 4
-
man oh man....if you only knew...it takes me more time to clean up the area just to film, than to do the vid......I roll...thanks for all the comments
2 years ago 2
All Comments (22)
-
Thanks or sharing your knowledge.
One point though.... You say a couple of times in the video that the jointer makes parallel surfaces, and when you finish squaring up to edges you say the two faces are parallel. There not parallel, they're perpendicular. Big difference.
-
nice
-
Jesus Christ. Thanks man. Bought my first jointer a month back and couldn't get it to shave the boards straight. Watched your vid, raised my outfeed table and we are in business. I was a bit miffed at the fact I couldn't get a straight board. Both ends were doing what you described as "snipe". Getting knotty alder dust in my keyboard now. Thanks again.
-
Thanks for your help. You are both funny and very informational. Thanks for making it real.
-
Set the fence to 90deg. Plane the wider side putting the hollow side to the bed to a flat finish. Turn through 90deg again with the hollow side to the bed, and the planed face up against the square fence, and plane until straight. If you are planing two pieces put them edge to edge and you should not see a gap if the cutters are set correctly. We call it a Surface Planer in England.
-
Teeeee heeee he. "This piece of Ash" :49.......I gotta' get me a piece of Ash. Love it! You are doin' a great job Bud. I learn a lot from ya! keep em' comin'
-
Hi, Just looking for some advice on plaining and thicknessing really large and long boards e.g 300mm wide and bark on the edges. . All the proper moisture content etc. The planer thicknesser im using can handle up to 300mm wide. Thanks James
-
Very helpful, thanks for taking the time to share your knowledge with the rest of us.
-
Great video. Finally I can look this darn machine in the eye!
Cheers
-
this is by far the best video on how to use a jointer. screw expert vilage and their hee-haw presenters
- 5:27
Cutting Thin Strips on the Table Sawby InTheWorkshop134,248 views
- 13:52
Tuning Your Table Sawby InTheWorkshop22,391 views
- 9:06
Get the Rock Outby InTheWorkshop7,906 views
- 6:54
Screws - Some Tipsby InTheWorkshop33,265 views
- 8:44
Grizzlyby AmericanWoodworker18,069 views
- 2:53
Planing rough-sawn lumber with a jointer and planerby thefamilyhandyman18,017 views
- 1:46
Building the Ultimate (and I mean Ultimate) Shop Stool. DVD and INCLUDED Templatesby TheFinewoodworker76,546 views
- 2:30
Planing boards wider than your jointerby Matthiaswandel54,729 views
- 1:26
Scary Sharp Demonstration 01by kiwa200638,437 views
- 3:18
How to use the jointer movie.wmvby thcisuper8186,662 views
- 7:52
Woodworking HAMMER A3 31 Planer-Thicknesser - Felder Groupby helfel0116,535 views
- 0:44
jointer dime testby eliwellis20,056 views
- 2:03
Cutting Rabbets on Your Jointerby handi4510,503 views
- 0:57
Creating Raised Panelsby nsirek27,915 views
- 3:43
Jointer Blade Maintenanceby smaxwell19636,265 views
- 6:34
Woodworking HowTo - Arched-Top Keepsake Box Part 1 (of 2)by EagleLakeWoodworking112,799 views
- 3:03
reclaimed wood topby sowason229,059 views
- 14:34
Woodworking #16- Cutting Your Own Veneerby TheWoodWhisperer137,900 views
- 2:08
THICKNESS PLANERby yairfe125,380 views
actually what i do is to keep pressure on the back as i start thru then transfer my pressure to the front after i reach the halfway point, if i am jointing something that has a ggod size bowin it and i am forced to joint it with the bowed side down the above will not work, in this case i keep the pressure on the infeed side ( starting side)...
InTheWorkshop 2 years ago