Fisher Paykel Dishwasher Servicing Fisher Paykel Dish Drawer Repair

http://www.ApplianceRepairLesson.com

This video explains how to repair a Fisher and Paykel dish drawer. F&P dishwashers have common issue with F1 and F2 errors as well as leaking. Following the directions in this video should help you repair your appliance.

Category:

Howto & Style

Tags:

• Kitchen
• Aid
• Dishwasher
• Fisher
• Paykel
• F1
• error

[owen2005]

I have removed the top drawer and rechecked the top drawer action and find that it is struggling to drop at the front and looked like it was getting a little stuck. I loosened the foam around it but Would I be better to put a bit of oil on the contact between the moving parts that go down.

Thanks for your help, you saved me a lot on money here

Owen

[ApplianceAdvice]

@owen2005 Right on friend:) Glad we were able to assist you. Thanks for taking the time to drop us a thank you note:)

[owen2005]

I have an F1 error code and I have dried out the pans, the F1 code comes on and a noise like trying to empty the Drawer. I have done the diagnostic check but there is no movement on the rotor or the lid. I have checked impeller and although 1 is worn the other is fine, the The F1 error comes back on again and I have to turn off again.

Is there something else that I can try?

Owen

[ApplianceAdvice]

@owen2005 Hi, if the F1 error keeps coming back there is water in the base or the filter board down there could be giving a false signal that its shorted..

[MrLooster]

Thank you so much!!!! I was pulling my hair out with three children and husband at work. Had it sorted in 2 mins after watching your video. You are a saint!!!!

[ApplianceAdvice]

@MrLooster Your very welcome friend!! Glad your back up and running. Thanks for taking the time to leave a comment.

[sirpinketalfonzo]

thank you very much sir! ive now used both of your repairs! :D

[ute445]

thank you for the help

[jezjonson]

I have the exact same dishwasher and mine will not empty. The red fault light is not on and I have no error messages. What do I do here? Is the drain tube blocked perhaps?

[tomcliffordwaldron]

my top drawer stops gets stuck mid cycle. when i open the drawer the water only feels luke warm so i am thinking it is the heater element and the drawer is not moving onto the next part of the cycle as the temperature sensor is not sensing that the water has reached a high enough temperature. can anyone confirm this. would anyone recomend me filling the drawer in diagnostic mode turning on the element and then using the temperature check to see if it heats up?

[TheGoldenhare]

A big thank you all the way from Scotland! Just managed to remove drawers myself to remove machine! I was trying to do this for hours before I watched your video. Thanks again, Corrina

[parisheavymetal]

Thanks for the video guys. I had the F1 problem and by following these instructions i managed to fix it.

[qingqing13]

I cannot start dishwasher...followed all directions shown here. No water in pan. The gasket has a bit of 'chewing'. I push start and get a few little notes...deh dehdeh deh...no better description: no action. The panel works.No 'F' symbol...just the little song when I press start. We have very hard water that we soften but the inners of d.washer dulled...I run a cleaner through every couple mos.

[owen2005]

Thanks, I eventually got rid of the F1 error by taking out the electrical board and hairdrying the whole bottom and board.

That fixed now the problem is that my top drawer is leaking when it is on. I have looked at the inlet and outlets but nothing there and changed the rotary thing in the centre (can't think of name) but I suspect the top lid isn't coming down correctly on the drawer but have I a way of checking that? Could there be leaking from the underside?

Thanks for reply

Owen