Lee Safety Prime Operation
Loading...
Loading...
26,099
Link to this comment:
Share to:
Uploader Comments (Abenedict1)
see all
All Comments (15)
-
thank you for pointing out the position of the arm in relation to the trigger. I found the solution to my problem.
-
Thanks a lot. I was referring to the primer pocket on the brass, I'll take your advice and not worry about it. I figured if there wasn't a stage built into the press for primer pocket cleaning then Lee didn't think it was necessary but I just thought I'd check. Thanks for the video, very informational.
-
I am not co ordinated enough to do this, I think I'll get me a single stage press lol
-
Great instructional video. Thanks so much
Loading...
- 0:53Reloading 9mmby JohnVH54128,748 views
- 0:42Installing Lee Safety Primeby LeePrecisionInc5,912 views
- 1:31Lee Loadmaster Automated Primer Systemby shadowdog50012,311 views
- 4:08Lee Safety Primeby bgallaher772,944 views
- 10:42Lee Classic Turret Press Review 2by ammosmith30,806 views
- 1:55Lee Classic Turret Press in Actionby bgallaher7718,032 views
- 0:30Lee Safety Prime - Priming .223 Brassby Liberty4Ever18,872 views
- 8:34reloading 200 rounds 30 mins RL550Bby PorterhouseV282,018 views
- 7:05reloading .45 acp with lee turret pressby Ignerence23,451 views
- 1:02Lee pro1000 9mm case collator modby stockdue14,731 views
- 3:58Lee Factory Crimp Die.by ammosmith55,125 views
- 0:24How to Remove a Stuck Caseby Esheato13,535 views
- 1:33Lee LoadMaster .223 Turret Style Reloadingby Liberty4Ever111,175 views
- 0:27Lee Turret Press Primer Arm Bindingby LeePrecisionInc5,306 views
- 6:38100 rounds on a Load Master in 6:37by DarwinTe64,954 views
- 18:15Lee Precision Classic 4 hole Turret Pressby Iraqveteran888838,876 views
- 10:46Lee Classic Turret Press and Safety Prime - Par...by sfliberal3,272 views
- 8:54Making Ammo on a Lee Pro 1000 Progressive Press...by sfliberal43,508 views
- 2:36How to Reload a 38 spl. and kill a beerby jeffreyclay93,197 views
good video thank you. I'm having a major problem trying to keep the primer holding rod from falling off every time its cycled.
Any advice?
It seems to be sticking to the shell holder, I've cleaned and lubed it to no avail. I have even grinded down the outside of the pocket. I'm starting to give up hope.
jbenetat 1 year ago
@jbenetat
Make sure it is engaged inside the ram. Sounds like you don't have it placed properly. It also could be you have the wrong shell holder in the press. If that doesn't work get on the phone to Lee and ask for Pat. He is the expert on all this stuff.
Abenedict1 1 year ago
What's your opinion on cleaning the primer pocket, is it necessary or should I not worry about it?
dahelmetrk 2 years ago
Don't worry about it. I assume you are talking about the cup that the primer drops in from the Safety Prime trigger? If you are talking about primer pockets on brass I would forget that for sure. My rifle shooting buddies will do that for high power, high pressure loads but for normal pistol and rifle stuff it is not needed.
Abenedict1 2 years ago
where do the spent primers go?
robert02109REO 2 years ago
There is a plastic tube that comes with the press which is attached to the bottom of the ram with a nipple. The primers go right out through the tube and into a waste can, usually I use an old coffee can, on the floor. It is the best spent primer removal system going!
Abenedict1 2 years ago