HOW TO ADJUST SNOWBLOWER ENGINE SPEED GOVERNOR
Loading...
Uploader Comments (donyboy73)
All Comments (95)
-
I removed the governer arm when replacing the fuel line. Upon reassembly motor was taching at 4500RPM!!! You solved my problem. Thanks for the helpful video.
-
SPOT ON! This is exactly what my problem was, I had the gov linkage set way to far back from where it should be,m next time ill take pictures and come back to your videos!
-
Great instructions. Very helpful, thank you!
-
@ConkersBFDN64 I think you may have to pull the cylinder cover off and see why the governor isn't working.
-
I got mine running great today. FYI, the length of the longer rod (the one from the governor to the throttle control) is about 6.5 inches and the shorter one (the one from the governor to the carb throttle) is about 4.25 inches. Thanks for the informational video. Also, the position of the rods seems to be important. I had the longer rod in the wrong hole. I used the hole that's in your video.
-
@donyboy73 The carb is exactly like it was before I did the other repairs. Can you give the length of both rods; the one that goes from the governor to the carb throttle and the one that goes from the throttle actuator to the governor? I realize they have bends in them for clearance, but how about the measurements from one end to the other? On other words, from one "z" bend to the other end with a "z" bend? Don't include any bends in between. This would be greatly appreciated.
8:36
HOW TO ADJUST SNOWBLOWER CARBURETORby donyboy7387,234 views- 2:27
How a TECUMSEH FUEL CAP can Give You Problemsby donyboy7315,110 views
- 5:37
HOW TO Remove & Clean Fixed JET on Snowblower Carburetorby donyboy7344,742 views
- 11:52
Governor Adjustment and How They Work Honda Briggs Tecumseh Kohler etc.by sixtyfiveford11,099 views
- 9:16
How to adjust carburetor mixture screwsby WhoSaidTyler86,655 views
- 1:49
High RPM Ford engine Blows upby Rillichefen205,243 views
- 8:24
PART 2 HOW TO replace Friction Wheel Disc on MTD Snowblowerby donyboy7315,474 views
- 1:01
Small engine animationby KAPORALDANGER698,451 views
- 15:26
Toro Snowblower won't start, Gummed up Float Bowl.by poolfixer3,921 views
- 0:29
Boss 429 dyno blow up!by bossofu792,104 views
- 7:57
HOW TO REPLACE CARBURETOR DIAPHRAGM ON TORO 2 CYCLE SNOWTHROWER PART 2by donyboy7312,688 views
- 5:15
Fixing the throttle governer linkageby TheCaptainD8219,960 views
- 9:16
Tecumseh carburetor rebuildby mbyr3171,174 views
- 3:11
8-11hp Tecumseh Carburetor Linkage Configurationby donyboy7324,351 views
- 9:05
how to adjust a mechanical governor on a lawn mowerby jay15kz52,980 views
- 9:58
HOW TO REBUILD Carburetor on 4-5HP Tecumseh Snowblower Engine Part 3/3by donyboy7319,596 views
- 6:44
Snowblower - a bit modified...by Thebestyoucanget331,812 views
- 9:43
Snowblower Tune-up (Tecumseh 5.5 hp) Part 2by mikesequiprepair34,361 views
- 3:50
how I made studded tyres for my xr650rby RickaVas160,324 views
Nice video. My Tecumseh is exactly like the one you are showing. I just put it back together after replacing a valve spring retainer. The problem I'm having is the engine RPM surges back and forth. Any ideas?
allake2011 1 month ago
@allake2011 that would most likely be due to carb settings or a dirty carb
donyboy73 1 month ago
mine runs too rich how can i fix this,,,
camry01 3 months ago
@camry01 thurn in the bottom screw
donyboy73 3 months ago
What can I do about the RPMs going up and down constantly. Reving up and down, up and down, up and down ?
Thank you,
John
dovepick 11 months ago
@dovepick first thing to do is clean and rebuild the carb
donyboy73 11 months ago