Wiring diagrams for HHO Cells

Since I dont know much about installing these cells, I have been doing some reading on it.

Anyway here is some info I hope will help others like me in regards to wiring & what goes where when it comes to cell wiring & installation.

Steve


p.s. This is for informational purposes only - so if you blow up your vehicle, its not my fault

;)

Category:

Education

Tags:

• AlmostHydrogen
• HHO
• stanley
• meyer
• fuel
• cell
• booster
• wiring
• diagram

[milacute04]

ok, i just got my efie, it only has 3 wires, those wires says in, out, and neg. but what about the pos??? can you or anyone else help me how to hook this up, i have a 95 integra... thanks

[AlmostHydrogen]

perhaps the o2 sensor wires provide the pos?

not sure about hooking it up cause I havent done this yet either. did you get directions with the efie?

[HydrogenBuster]

Good Job AH! You are really progressing well! All of your data is correct. You are right to have a bypass switch in the cab to over-ride the relay. Be sure to turn off the O2 simulator when you kill the generator. Also to have the relay powered by your ignition switch in case you forget is a necessity. If I might add, you only need a relay equal to your fuse. Be sure to get one that has a minimum (open or close) the amperage is different for each function. Keep up the good work!

[AlmostHydrogen]

thanks but I still have so much to learn - slow and steady.

:)

[AlmostHydrogen]

Yes I have seen systems with pumps too - looks interesting and definetly something if heat is a problem.

[FluxCapacitor2008]

Great info

Where can I get the cool CAD drawing software?

[AlmostHydrogen]

actually its not a CAD program, just MS Powerpoint using the drawing tools & the custom animation effects. After that I run the slideshow and record it using iShowU (a mac program).

Its not cad, but it does great for stuff like this.

[gvigilgem]

That was an awesome presentaion! thank you for explaining everything so clearly. Im uilding my first cell and am having trouble figuring out how to seal the pos & neg on the top so i dont lose pressure. What is the config for the terminals using olts and washers?

[gvigilgem]

That was an awesome presentaion! thank you for explaining everything so clearly. Im uilding my first cell and am having trouble figuring out how to seal the pos & neg on the top so i dont lose pressure. What is the config for the terminals using olts and washers?

[fuelban]

nice video, we explained and shown too, I must admit, wiring is not my strong point either, LOL, thanks.

thom.

[urbex2007]

You forgot to say how it is wired to the car ECU so it knows to reduce fuel input when you send hydrogen in. At the moment you are using MORE fuel due to extra load on the alternator. There is nothing to control the fuelling at present, not only on your system but everyone elses. This shows it is a complete scam, it shows a basic misunderstanding of the way the car engine works. How can so many people be so ignorant as to how an engine works!!!!!!!!!

[lazzer408]

Run 12v to the relay coil and low side switch the relay to ground. Only 3 wires are used to the relay and only one of them is needed to go into the vehicle cab. Ground the wire, relay turns on. Less wiring. Less chance of error.

[alor54]

do you know you can wrap 3 strips of alfoil over the sensor body to mask the signal, I have done this on 4 cars and it has worked very well everytime...

[Spicygarden]

Mr. Steve, would u please help me, why my fuse 25A always damage(shorting)& hot cable in my hyundai tajet 2700cc, batt 12V 80AH, Hella relay 30A, HHO cel smack + NaOh 10A, thanks William,Jakarta,Indonesia

[subatron]

Try using one solar cell as a interrupting ecm or brain box this will fluctuate up and down pass the illegal .45 volt + or - this reading will keep the brain guessing as light will not hit the solar cell at a perfect rate because of miner ambient light changes. cheap way I think will work