Part2 Replacing Control Arm Bushings
Loading...
Loading...
51,106
Loading...
Link to this comment:
Share to:
Uploader Comments (mycarsr)
see all
All Comments (13)
-
@theciskokidd usually they just wont extend far enough to fit all the parts.
-
dude, that sleeve to keep the fingers straight is an awesome idea. thanks! Imma copy it.
-
So chanced are this isnt possible with a little bit smaller vise? Will I just end up bending the tightening arm on the vise?
-
I would like to make a press out of a bottle jack.
-
you sure like to do things the hard way dont you!
Loading...
- 2:48
Rubber control arm bushing replacement overviewby elephantracing71,176 views
- 0:49
Bushing Removal Without Smokeby MX5hyde25,276 views
- 0:25
how to remove a bushingby Seisephiroth42,378 views
- 5:39
CONTROL ARM BUSHINGSby POLYBUSHINGS31,398 views
- 0:06
Front Lower Control Arm Bushingby iametarq30,798 views
- 4:23
How To Remove Control Arm Bushingsby Quiroz92186,699 views
- 3:43
How To put in Polyurethane Bushings (Energy Suspension Bushings) For a 2 Gen RX-7(FC3S) Part1by MrDriftoDrifto17,913 views
- 5:52
how to press in a bushing in an upper control arm.wmvby 7impala16,640 views
- 0:29
VERY BAD Ball Joints - WATCH THIS!!!by haglinautomotive197,499 views
- 12:10
Remove/replace lower control arm, 4th gen Maximaby boredmder12,416 views
- 1:06
Bad LCA bushingby AdrenalineJunkie121820,361 views
- 2:53
Lower Control Arm Toolby richpowerhk79,600 views
- 5:45
Removing Rusted Control Arm Boltsby richpin06a25,511 views
- 0:22
Redneck bushing pressby bassoonisbetter8,542 views
- 6:25
e46 m3 Rear Trailing Arm bushing remove and install RTABby HighPoweredLasers26,249 views
- 1:18
Dodge neon control arm bushingsby BMAN11046,391 views
- 3:01
Upper Control Arm Bushings Honda Accord 96.movby sexymd3912,107 views
- 0:50
Pressing in Front Control Arm Bushingby cncmastr13,389 views
- 3:27
URO Parts Porsche 911 Front Control Arm Bushingsby uropartsdotcom11,797 views
- 2:31
Replacing A Lower Control Armby scottykilmer24,914 views
Good video, I'm gonna use your idea. Except in an arbor press. My hydraulic press will not work because the other end of my control arm gets in the way. Thanks for the info
VCschwabby 2 days ago
@VCschwabby
Yes I have a press now also. Didn't have one at the time..
mycarsr 2 days ago
Probably would be very hard on the vice. I have since picked up a 12 ton press from Harbor Freight to save wear and tear on my vice. BTY the vice was an estate auction purchase for $20.
mycarsr 1 year ago
You have to make do with what you have on hand sometimes.
mycarsr 1 year ago
About to put some in my 86 town car. Thanks dosent look to hard at all!
Majorbud 2 years ago
I'd rather use a press but have not got one yet so the vice is the next best thing. Be sure you have a large vice though if you don't have a press.
mycarsr 2 years ago