Yamaha G1 golf cart motor mod
Loading...
Link to this comment:
Uploader Comments (03jayco)
All Comments (15)
-
You still have this G1?
-
How do I find a 34mm carb and adapter that will work on my 2-stroke G1? Thanks!
-
lol, i have a 1979 yamaha g1 gas 2 stroke golf cart and it is the fastest golf cart around it will do 28 mph stock with out the govnor being wide open, its never been rebuilt and i just checked the compression and its blowing 128 now im curuntly bulding a lift kit for it, the g1 isnt the nicest looking but for speed i highly recemend it
-
HI WATS UP
-
Thankyou for responding, what you described is what I had thought about doing also! I have turned the governor screw in all the way and pitched the lock nut. The cart will do 20 mph with 2 on board and almost 22 solo.......that is without any mods...so far!
-
My uncles is ported, polished, but thats it. If I buy it what should i to, motor-wise?
- Loading comment...
11:34
How to convert a Vertical shaft engine to run horizontallyby kougsohv950,219 views- 7:45
Clutch Kit Maintenance Pt.1by mxzxRevzone105,205 views
- 3:39
100hp golf cart wheelieby briparts51,015 views
- 2:36
electric to gas golf cart of deathby hvguy7,094 views
- 4:27
Neurotikart II: Using a golf cart motorby wires99143,904 views
- 5:36
900cc golfcartby chrisvogel88390,998 views
- 3:44
golf cart buildby amygem287,577 views
- 3:26
Golf Cart 440 Polaris Snowmobile Engine Liftedby TroyM4x421,983 views
- 2:45
Fast Golf Cart Fixby pacificcloud9,274 views
- 2:01
golf cart doughnut /burnoutby mattbhill8,184 views
- 2:00
Yamaha G1 golf cart ebayby mweba11,172 views
- 1:21
redneck mods to golf cartby bamasranch1,988 views
- 1:05
FREE GOLF CART! project stupidby backyardjay5,681 views
- 4:07
Tim on his Yamaha G1 Golf Cartby bikegeekmtdx1,555 views
- 0:30
Yamaha G1 buildby fish5131,253 views
- 2:17
ez go golf cart with quad engine 5 speed semi-autoby vinnieres2,992 views
- 1:44
yamaha r6 powered golf cartby jspecjoe20,448 views
- 0:43
Yamaha golf cart G9 clutchesby clonecart12,750 views
- 2:21
Off Roading in Yamaha G2 Golf Cartby weekendwarriorfsw325,295 views
TheBigfootkiller ,
If I was gonna do it over again, I'd go with a 30mm or 32mm Mikuni VM series carb.
The 34mm works good, but is very difficult to jet because it is really too big for the motor. It's still running very well 4 years later, but due for a top end rebuild. You can find a 30mm VM Mikuni on ebay pretty cheap. Buy the rubber flange that is made for the 30mm, and then make the adapter plate.
03jayco 4 months ago
what did you do with the govenor? Did you bypass it or something else? I just bought a G1 and have adjusted the govenor all the way as fast as it will allow and it is still too slow for what I want. Any thoughts? Thankyou for posting!
Ulai777 1 year ago
@Ulai777
I removed the governor. You don't need to remove it like I did. The bracket on the governor shaft(sticking out of the differential) has a "D" shaped hole in it and clamps to the governor shaft. If you drill the hole out so it is round it can rotate on the shaft. Just don't tighten the clamping screw. That effectively bypasses the governor.
03jayco 1 year ago
The head is shaved .030". Exhaust butterfly removed. Intake and exhaust ported and matched. Governor removed. 34mm Mikuni carb and adapter plate installed. UNI air filter installed. New piston/rings/bearing/gasket set.
03jayco 2 years ago