2003 Honda CRV Brake Pad and Rotor change part 2
Loading...
Uploader Comments (ajchien)
All Comments (11)
-
I was trying to determine how the pads on my 2005 CRV Tdi were removed from the top and bottom clips with the help of the new Hayes manual for that model. In most cars one takes the clips off the caliper THEN you remove the old pads. But I see from your video that the pads come off at right angles to the disc and the top and bottom springs remain in place until the pads are removed. That was not made clear in Hayes manual so I'm grateful for your video!
-
Thanks...from a woman. I actually used this video and have been changing my brake pads for the past yr!!!
-
Vary clear video.
Thanks
-
great video,i love it.thankss.i had a crv to similar to yours.and am gonna try to change my brake pads .that was easy after i watch ur video
-
Also similar on a range rover - well done very helpful
-
Thank You for the valuable information
7:04
How To Install Replace Brake Pads and Rotors Dodge Durango Dakota 97-03 1AAuto.comby 1aauto105,812 views- 0:33
Unlock your car with a tennis ball!by 11beeber1,796,826 views
- 3:44
Bleeding rear brakes how toby fishycomics89,820 views
- 4:28
2003 Honda CR-V serpentine belt changeby ajchien25,709 views
- 3:39
rear brake rotor 2002 crvby fishycomics11,782 views
- 2:03
Honda CR-V @AWD Party 2009by sdegdeg22,753 views
- 4:13
2003 Honda CR-V spark plug changeby ajchien44,680 views
- 1:42
Honda CR V Crossing Streamby ajp4210997,480 views
- 7:36
Rear Brake Pad & Rotor Replacementby richpin06a39,762 views
- 8:20
How to: Replace a timing belt and water pump - part 2by frylockthefryman214,043 views
- 4:59
How to change Rear brake pads on honda accordby barakatmo16,721 views
- 8:36
Rear Diff fluid change how to:by fishycomics13,043 views
- 6:39
How-To Install New Brakes & Rotorsby motorztv484,453 views
- 4:06
Oil change how toby fishycomics11,035 views
- 1:25
2002 Honda Crv Ex Brake Fluid change how toby fishycomics2,689 views
- 9:00
DIY: How to install Drilled & Slotted Brake Rotorsby ocautosports007120,425 views
- 2:11
How To Bleed Air Out Of Your Car's Brake System.by scottykilmer261,985 views
- 4:10
How to replace rear brake pads on a Honda Civicby thepoutinedotcom56,526 views
- 20:16
Honda front brake job - caliper and rotor replacementby ManClubAustin18,180 views
How come you didn't show yourself using the caliper tool w/ the old pads to push the piston back in place? That's crucial.
rodneytheram13 2 years ago
At 1:44 I push the caliper back in with a 4 inch c-clamp. This was done with the brake fluid resevoir opened. Alternatively, I've done it with the bleeder bolt open.
ajchien 2 years ago
how do you get the rotors off i took the screws out and the nut but rotors wont go
Built94FordTuff 2 years ago
Do you see those additional screw holes (that did not have studs going thru them) in the new rotor I installed? If you have those holes then you can put screws IN thoses holes to PUSH the rotor off the hub. Or you might consider using a "liquid wrench" substance plus a hammer.
Good luck!
ajchien 2 years ago