How to change Valve Seals on Engine head.wmv
Loading...
Uploader Comments (juniorrc2003)
All Comments (11)
-
@juniorrc2003 Thank you! i have changed them :) also, i would like to add some tip i discovered and i'm sure that i'm not the first one did ! lapping valves with drill and thick rubber washer glued to 12mm bolt which is hold by the drill. worked perfectly and the results were great.
-
@juniorrc2003 damn, it begins smoking about a minute after the cold start, then when the engine is hot enough I ride it and it becomes less smoky, Dont wanna spend another $350 fixing it!
-
@TX97SR20DET Sure do. Click on my user name to see my other video's and then look for the one about changing valve springs, and it talks about installing the springs and retainers.
Enjoy
-
Good vid. I have an mild PP SR20DE head that I just got back from the machine shop. Did you make and videos of reinstalling the valve, spring, retainer etc?
12:11
Fitting new valve guide seals without removing the cylinder head Suzuki Vitaraby richardcloudbase37,554 views- 9:21
Valve seal Replacementby realfixesrealfast95,508 views
- 6:05
Cylinder valve leakby slymee836,670 views
- 1:46
NO BRA?!?!by N3rdGurl1018,098,085 views
- 14:57
How to replace your head and head gasket pt. 1- 1992 Mazda B2600iby mrmaxstorey63,214 views
- 0:58
Testing for Leaking/Bent Valvesby bgoodrick24,941 views
- 6:16
Basic valve jobby Thebroncobillshow103,841 views
- 2:34
Valve spring compressor remover tool demonstrationby grjr6,570 views
- 4:52
Replacing Valves on Engine : How to do Guide Sealsby UniUnited10,081 views
- 4:31
Stupid people doing stupid thingsby GaloreVideos7,224,227 views
- 8:21
Grinding Valvesby FerdinandMagellan0816,641 views
- 1:55
Enginebasics: How To Install Valve Springs.wmvby juniorrc20032,391 views
- 4:20
Quick valve job with 3 angle form carbide blades..wmvby cylinderheadshop19,639 views
- 0:51
Blue smoke at idle because of engine sludgeby intelagense1,697 views
- 1:13
bad valve seals or piston rings??by remmillie7,760 views
- 0:40
LS Valve Spring Compressor by PROFORMby PROFORMLou9,990 views
- 4:49
cylinder leak test how to check for bent valvesby pls5220218,658 views
- 6:12
valve stem sealby buddycraigg1,110 views
- 4:16
How-To: Polish Cylinder Head Exhaust Portsby MechanicDave8495,502 views
Nice video by the way, i have a small question. in my case (ford probe 2.0) the valve seals are not easily accessible on the head like the one you are working on. so can't use my hand, the socket is a must in my case. which socket should i use? the one that's its circle is bigger than the upper ring on the valve seal?
mbarizia 2 months ago
@mbarizia On the valve seal you want to choose a 12 point socket that will push on the lower/fatter bottom part of the valve seal to push it down and seat it. Make sure to be gentle and that the socket is small enough to fit over the top, but can push down on the base of the valve seal securely.
juniorrc2003 2 months ago
I got a problem with my quad, it smokes alot (burned oil) could it be the valve seals or the piston rings? I just changed the piston rings about 2 months ago
eljoelin 6 months ago
@eljoelin Maybe your rings didn't seat right. If you get A LOT of smoke when you engine break the motor, then its usually valve seals.
juniorrc2003 6 months ago
Can I use oversize valves with SR20DE(T) ? Can I get any performance?
Awesome videos, keep posting :)
MrRadjevic 7 months ago
@MrRadjevic You can, but the head would need to be taken to a machine shop and the valve seats would need to be re-bored out and machined to accept the over sized valves
juniorrc2003 7 months ago