DesignJet 750 / DesignJet 755 repair- Loading paper roll
Loading...
Loading...
2:52
DesignJet 450C- Loading paper rollby HPPlotter1,434 views- 3:48
Setup your HP750C plotter on Windows 64Bitby selectshots2,363 views
- 0:51
HP DesignJet 750C 36" Color Printer Plotterby btjohnson99995,005 views
- 5:45
DesignJet Repairs - DesignJet 750 & 755 network setupby HPPlotter639 views
- 2:15
DesignJet 450C repair- clutch errorby HPPlotter1,361 views
- 3:54
Designjet 750c Carriage Assembly and Belt Replacementby FixYourDesignJet1,768 views
- 3:04
HP 1050C Plotterby medasbabu1,744 views
- 3:14
printser designjet 750cby printser20082,312 views
- 1:15
Canon IPF605 A1 Plotter in actionby wydos12348,266 views
- 0:08
Plotter HP DesignJet 750C Plus - taglioby pfingherals513 views
- 3:10
HP Designjet 800 42" Plotting PDFby wydos12341,737 views
- 2:21
HP DesignJet 500 repair- Replacing print headby HPPlotter10,272 views
- 0:40
Designjet 750c Internal Partsby FixYourDesignJet318 views
- 2:06
hp designtjet 500 large print plotterby djusaneon6,161 views
- 1:46
DesignJet 500 repair 21:10 error codeby HPPlotter4,302 views
- 3:55
DesignJet 450C repair- cartridge errorby HPPlotter3,089 views
- 1:56
HP 750C Plus Demoby MrStonecold1997378 views
- 3:41
HP T1200 HD MFP - Print/Copy/Scanby wideformatco2,409 views
- 1:55
Designjet 500 carriage belt replacementby FixYourDesignJet4,715 views
- 13:39
how to install a hp designjet belt 700 750c 755cm directions C4705 C4706-60082by BrokenPrinter1408 views
@chiefhighpriest
Out of media: DesignJet has come to the end of a roll.
If these messages are not correct for the given condition then you may well have a hardware problem.
It's difficult to ascertain exactly what is going on without being in front of the DesignJet, it worth checking that the media sensor is in place & both sensor flags are intact, this is located on the RHS of the print platen & should be visible from the underside of the DesignJet. It can be pulled down to unclip it.
HPPlotter 7 months ago
@chiefhighpriest
Hi,
Difficult to say, the DesignJet won't be displaying all these messages at the same time and may all be correct:
Load media: The DesignJet has a print job or alignment pending & requires paper to carry it out.
Ready for media: A normal message when the DesignJet has booted without any media loaded.
Media too small: Normally seen when a print head alignment is pending & you have loaded an A4 sheet, from memory I think the minimum paper size to run an alignment is A2.
HPPlotter 7 months ago
I have my paper loaded correctly and am getting the following three messages: Load media, ready for media, media too small and out of media. Faulty Printer?
chiefhighpriest 7 months ago
@chiefhighpriest
Thanks, glad you find them useful :-)
HPPlotter 7 months ago
You are a printer wizard.
chiefhighpriest 7 months ago