The Practical Skills Series : Cable Termination - SY Flex ["Electrical Jobs" / Electrician]
Loading...
Link to this comment:
Uploader Comments (learninglounge)
All Comments (13)
-
@88Ghillie yeah but the strands inside the cable need earthed as well.. just like swa gland
-
The flex looks as though it already has an earth in it?
-
@chiefbag ---- The 'Earth tag' is also known as a 'Banjo' in the trade. ;)
-
0.59.........Cosmic apperance? haha far out man!
-
The "Earth Tag" as you call it should be located inside the enclosure you are terminating the cable to.... Am I wrong or Am I right.
Amateurs with no experience or electrical competency.
-
Never mind the "R" or lack there of. For any person or electrician that may be watching this, the obvious solution for cutting the braid is to pull it down toward you and therefore not risk cutting the inner rubber. Again do the same for splaying except use a small flat screwdriver.
-
The stress of AM2 LOL.
-
this is really good for anyone about to do the am2 and has not done much sy
-
I have found that if you push the brade from the top. To form a bulb at the start of the outer insulation. This helps to prevent scoring the inner isulation.
40:16
Paul Abernathy - Helping You Pass Your Electrical Examby ElectricalGuru6,951 views- 3:55
The Practical Skills Series: Cable Tray ["Electrical Jobs" / Electrician / "Electrical Training"]by learninglounge2,588 views
- 4:33
Conduit Bending How to bend a 3 bend saddle.wmvby pyrotech887714,505 views
- 5:20
high voltage cable termination.wmvby ariftuhama9,861 views
- 4:08
The Practical Skills Series : Cable Termination - MICC/MI/Pyro/MIMS ["Electrical Jobs"]by learninglounge9,035 views
- 5:11
CMP Products - T3CDS (Triton) Cable Gland - SWA DIRECTby CMPProductsUK10,649 views
- 8:37
The Practical Skills Series: Fitting BS951 Bonding Clamps ["Electrical Jobs" / Electrician]by learninglounge3,523 views
- 9:24
The Practical Skills Series : Cable Termination - Steel Conduit ["Electrical Jobs" / Electrician]by learninglounge6,338 views
- 11:05
Electrical Transformer Tutorialby Afrotechmods114,445 views
- 7:22
How to terminate Cat5e Cable - Heads, Keystones, Crossover, etc.by sewelldirect91,307 views
- 4:14
17th Edition Online Course from the ECA ["Electrical Jobs" / Electrician / "Electrical Training"]by learninglounge1,036 views
- 9:07
The Mighty Motor ["Electrical Jobs" / Electrician / "Electrical Training"]by learninglounge2,825 views
- 2:20
Chris Kitcher - Electrical Testingby EchoVideoProductions51,180 views
- 1:13
Insulation Resistanceby DJTElectrical19,304 views
- 5:41
Periodic Inspection Reporting ["Electrical Jobs" / Electrician / "Electrical Training"]by learninglounge11,448 views
- 1:03
Steel Wire Armoured Cable Tipby tradeskills4u11,358 views
- 1:51
Basic Electricity ["Electrical Jobs" / Electrician / "Electrical Training"]by learninglounge1,615 views
- 1:27
Electrician Training Videoby CareerColleges121,922 views
- 8:36
An Introduction to Protection for Safety and Fault Protection ["Electrical Jobs" / Electrician]by learninglounge2,730 views
- 2:21
Testing a Theory: Earth Leakage ["Electrical Jobs" / Electrician / "Electrical Training"]by learninglounge17,369 views
We have spoken to Mark and he has confirmed that the earth tag can be either inside or outside the enclosure - there is no preference made by the IEE.
Mark's personal take is putting it on the outside so it is easier to visually inspect. As Mark is a lecturer, we can assure you that he is not an 'amateur with no experience or electrical competency'.
The 'cosmic' appearance was meant to be cosmetic appearance - oops, slip of the tongue.
Thanks for all of your comments so far....
learninglounge 8 months ago