OUT OF DATE Part 3 Surf an Origami Hang Glider on a Wave of Air_More Construction.mov

THIS VIDEO IS OUT OF DATE AS OF AUGUST 23, 2010. THE REVISED VIDEO IS AT
http://www.youtube.com/watch?v=62gKLPUnTsQ

As you build and fly, here are some tips that I wish were in the video (updated instructional videos coming soon). If you keep these in mind as you go through the instructions, you might have a less frustrating time.

I no longer make a second glider out of the printer paper. It's just too heavy and I save time by just concentrating on the phone book paper one.

I no longer cut the notch in the front. I just fold that part now.

The center of gravity (CG) marks on the glider are starting points only. Adding more or removing weight shifts the CG forward or backward. This is very useful for dealing with stalling and diving.

Instead of straws for boom and weight, I now use the thin wire that's inside "twisties," those bendy things used to close plastic bags and also to wrap various cords when you first open the packaging of electronic equipment. I strip off the paper or plastic part off with pliers so it's more aerodynamic. When taped on, I can fine tune the by straightening the wire for more leverage (more downward force to counteract stalling). Or I can fold the wire back on itself for less downward leverage (if the glider is diving). It's easier than adding or cutting off tape.

When taping the wire on, fold that short, very front fold too, so the tape folds too.

The two diagonal folds near the front of the glider—the ones that make the under curve (camber)--have to be creased firmly to establish the folds. HOWEVER, when flying, they should only be bent enough to keep the glider from buckling (bending where it is supposed to stiff enough not to bend). Too much fold, which causes too much camber, makes the glider dive uncontrollably. The boom weight in the front also pushes the front down, but its push is self-limiting. Not so the front (leading edge, LE) if it's bent down too much—it pushes the glider down harder when it's divining. A good way to limit the camber is to stick the glider in the middle of the phone book and close it. In a few seconds it seems to flatten the glider just enough.

I have concluded that a well adjusted glider does not need the vertical stabilizers at the sides. That reduces weight in the back, which means a bit less weight needed in the front, so it's a bit more efficient. If you cut off the stabilizers, just round the sharp corners a little.

When learning to fly—before you use your hands to create the air wave—I am finding something small that can be held with one hand, like a breakfast cereal box, works better than something big and bulky.

Category:

Science & Technology

Tags:

• walkalong glider
• controllable slope soaring
• science project

[Sprax101]

what site did you get the cut out??

[sciencetoymaker]

@Sprax101 I don't understand your question. The pattern??

Slater

[hollieandsusanrule]

Oh man. This is hard!! It flies for like half a second and flutters to the ground...

[sciencetoymaker]

@hollieandsusanrule Please note that this video is now out of date. I have a new design, new pattern (EZR) and new video instructions. Go to sciencetoymakerDOTorg for the correct links.

Slater

[sciencetoymaker]

@qwerty81071 I've seen David Aronstein do loopty loops but I've never been able to do it. I'll try again!

Slater

[qwerty81071]

@sciencetoymaker Hi Slater, I practiced and was able to fly the glider with my hands, but the point is that I found out you could do back-flips or loops using the glider, better to use cardboard so all you got to is to gain some altitude and twist the cardboard forward quickly what this does is it sends a gust of wind to the front causing the nose of the glider to rise quickly, with a little practice you will be able to get it perfectly thanks. Deshitha

[jerielho1234]

@sciencetoymaker ya da pattern

where is it??

[peterhahaha1908]

do you have plan in order to print??

[Sprax101]

@sciencetoymaker yeah i guess? xD

[sciencetoymaker]

@merrymerelyn Do you mean the pattern?