shotgun fitting
Loading...
Loading...
22,669
Loading...
Link to this comment:
Share to:
Uploader Comments (WillLeviMarshall)
see all
All Comments (8)
-
So tell us how it worked out for you, did it work?
-
Hi Ian the action was removed prior to steaming.
-
You will have to stip and clean the action after steaming a stock like this.
-
How well did this work? I need to increase the drop on my stock and am thinking of trying this.
Loading...
- 6:12
Does Your Shotgun Fit? Excerpt from GunTech Video Magazine #46by AmericanGunsmith13,158 views
- 2:14
How To Achieve Proper Length of Pull (Part 1)by scheelsadmin28,291 views
- 1:39
QB79 stock from scratch to rangeby ExoticWoody86,314 views
- 1:31
Length of Pull - Making It Nearly Perfectby MidwayUSA51,093 views
- 4:55
Understanding Gun Fit - NSSF Shooting Sportscastby TheNSSF25,349 views
- 2:51
Gun Stock Refinishing: AGI 400by AmericanGunsmith36,666 views
- 1:29
Repairing pitting in a shotgun barrelby MidwayUSA111,292 views
- 2:59
Installing Rifle and Shotgun Recoil Pads: AGI 324by AmericanGunsmith18,619 views
- 1:30
How to Install Recoil Padby MidwayUSA20,297 views
- 1:13
Master Gun Mount Fundamentals through Repetitionby DucksUnlimitedInc21,223 views
- 5:09
Sanding and Finishing Boyds' Gunstocksby boydsgunstocks133,218 views
- 0:56
Checkering a Gun stock timelapseby CaptainMurphyDUCK5,071 views
- 1:45
Shotgun Shooting Tips, Gun fit Partby OutdoorHub5,263 views
- 2:40
Top 10 Clayshooting Guns.by L7GGD202,657 views
- 1:29
Blue rifle using cold blue for a beautiful finishby MidwayUSA210,921 views
- 2:04
Shotgun Slip Stand Demo and fitting instructionsby 32712magpie3,309 views
- 2:18
Franchi Renaissance Shotgunby husnain6728,824 views
- 1:31
How to make a stock blank from a piece of lumberby MidwayUSA136,392 views
- 4:19
The Storm Report: Useful Gunsmith Tipsby PheasantsForever1,581 views
Yes worked fine make sure you carefully pack out where the action goes with wood so that the metalwork fits when your done.
Oh and also it springs back a wee bit 3 or 4 mm you need to steam for at least 1 hour per inch of wood so 2-3 hours should do it
WillLeviMarshall 5 months ago
Yes worked fine make sure you carefully pack out where the receiver goes with wood so that the metalwork fits when your done.
Oh and also it springs back a wee bit 3 or 4 mm you need to steam for at least 1 hour per inch of wood so 2-3 hours should do it
WillLeviMarshall 5 months ago
Oh and also it springs back a wee bit 3 or 4 mm you need to steam for at least 1 hour per inch of wood so 2-3 hours should do it
WillLeviMarshall 2 years ago
Yes worked fine make sure you carefully pack out where the receiver goes with wood so that the metalwork fits when your done.
WillLeviMarshall 2 years ago
Ohh it did work too I refitted the stock and never missed again... well it was an improvement at least!
WillLeviMarshall 3 years ago