1.875 Liters/Minute@11.2 Watts/ml ©

This cell is the same as before except I increased the flow of water through the cell by increasing the pump speed. The Pump was also change out because the wind shield wiper pump burned up. The Stats are as follows With Ultra-Sonics on 11.9V @ 29.2 Amps for 32 Seconds 11.12 watts/ml and 31.25 ml/s production rate. 5.4 MMW.
With the Ultra-Sonics off the Stats are: 11.9 Volts @ 28.7 Amps for 34S econds this is 11.61 watts/ml and 29.41 ml/s production rate 5.17 MMW.

Category:

Science & Technology

Tags:

• HHO
• Electrolysis
• Fuel
• Hydrogen
• OxygenTesla
• Browns
• Gas
• Jacob

[g0a23657]

are you still using 3tsp lye NaOH as your electrolyte in this video?

[AllgoodAutomation]

yes

[g0a23657]

are you using ss plate in your closed cell?

[AllgoodAutomation]

Yes 4X10 +NNN-

[adam3176]

Wow. Well i think if you had three of those i could drive around with full throttle and have enough gas without getting my Compressed tanks.. Are you in the seattle area?

this is getting close to On demand Hydrogen if ya ask me. I want to try breaking water into hydrogen other than electricity. more like microwaves..

[AllgoodAutomation]

You Otta see what 36 plates can do!!!

[bakupcpu]

Nice demonstration. So it seems that the ultrasonic device does help alot. My question will be for the pump. Is it use to cool down the Cell or simply to create a flow? Thanks in advance.

[whiterican74]

so far you have been the only person I have seen admit that amperage is the cause of heat within a cell.

[glider98]

need to know what frequency the ultra sonics is at. stan meyer used frequency adjustments to get voltage to do the work without high amps,reducing the wasted heat, cause by using high amps.

[john29302]

stick to mmw...why the new ml per second crap....yeah it bubbles....did you include power consumed by pump...oh then you are not doing science just showmanship

[eurekaH2O]

use head pressure instead of ultrasonics, put your plates at the bottom of a 7ft tube. organic acid works good for ion transfer, I use Acid blend from brew and wine shop. buy a ph meter and bring amperage to plate distance varied by ph levels. water stays clear with organic acid verses salt.

[bennytan777]

hi is that meter from harbor freight? I thought they were rated at just 10A, how'd you do it?

Thanks.

[zootsuit7]

I have read and seen a lot in the last month. From Youtube and -OU-. I have half-baked ideas, but perhaps you can help: 1) Can you use Cascade (dishwasher detergent) as an additive to modify the surface tension of water as effectively as ultrasonics? 2) What would happen if you add Ammonia to prevent freezing in winter? Does ammonia aid/reduce HHO production?

[zootsuit7]

3) To get the most surface area of your metal into the water, wouldn't a grid be better than a plate or even a SS mesh or SS cloth?! This along with a water pump or ultrasonic or Cascade to reduce bubbles getting in the way of your plates? 4) I have seen experiments from 6 volts up to 40,000 volts. Doesn't seem to matter nearly as much as the Pulse Frequency.

[zootsuit7]

Can you use a capacitance meter to quickly figure out a frequency to pulse the cell at? Has anyone tried to use a variable inductor in parallel with the cell to get things 'pinging' and cut power way back, similar to how a tesla coil works? Any coilers out there messed with an HHO cell?

[Caerus247]

i need a good forum... anyone?