Dime Size Heat Shrinking Metal With Oxy/Acetylene
Loading...
Uploader Comments (ButlerCollision)
Video Responses
All Comments (7)
-
be good to remove the paint first and how the hell can you planish when bonnets closed with out a flipper or dolly after. no mentin of heating the lowest spot to cherry red and no mention of dont let the tip of the flame touch the bonnet or it will harden the metal to much , mind you that flme what was that
-
This technique will come in handy to repair maple sugaring pans. Mineral build up at the end of a day of boiling eventually pops off in a little round bullet and the syrup quenches the spot creating an oil can. Good video. Thanks.
-
can you use heat gun to burn it? if i dont have oxy /acetylene?
-
You should the proper way to open the oxygen and acetylene regulators so you don't teach others the incorrect way. Turn the regulator screw out first then open the cylinder valve, then screw in the screw to get the pressure you want. many people do it wrong and ruin their regulators.
8:45
Dent Repair - Using a Weld-on Stud Gun To Repair Car Dentby ButlerCollision33,879 views- 3:36
How To Apply Fiberglass Filler to a Welded Areaby ButlerCollision21,688 views
- 2:56
Dent Repair Using Hammer-On-Dollyby ButlerCollision54,964 views
- 3:26
How to Hold and Dress a Body Hammerby ButlerCollision12,374 views
- 20:05
A Rust Hole and a Big Dent.by pisserschannel18,448 views
- 1:15
Removing oil canningby Tony158411,381 views
- 3:40
Metal Shrinking Cargo doorby bowatpa3,857 views
- 0:39
Metal Hammer & Dolly Workby jlillyresto18,654 views
- 2:06
"Flow forming" metal shaping with a rivet gunby specialseventynine27,313 views
- 1:00
Shrinking Metal with a Hickory Malletby tinmantech27,514 views
- 5:00
Shrinking sheet metal / steel with torchby vf400072,795 views
- 5:14
Shrinking Disc Video Trailerby ynotrocket23,864 views
- 4:51
Body Hammers and Dollies - Metalworking Tips from TM Techby tinmantech39,870 views
- 0:23
Oxy-acetylene Bomb!!!!!! Must See!!!!!!!by wargo5296,560 views
- 0:08
Flameless damage free Frozen or Rusted nut removalby wwwTHEINDUCTORcom71,625 views
- 2:15
Butt fusion welding - thin sheet mild steel (Panel Beating)by TAFESouthAustralia52,767 views
- 3:51
Creating half a sphereby LenapeFireTurtle52,632 views
- 27 videosMetal Formingt
- 7:26
Welding: Oxygen Acetylene - Kevin Caronby kevincaron33,967 views
- 2:41
Dent Removal Classic Car Restoration Part 1by jlillyresto36,988 views
Do you heat the high side or the low side...or does it matter?
omyajt 1 year ago
@omyajt heat the most stretched part of the repair area. Heat the high area, which will lower as it shrinks. If it starts to sink in you may need to support backside with dolly to lock metal in place.
ButlerCollision 1 year ago
I don't think a heat gun would target a small enough area or get hot enough. If you don't have a torch, you may can do it with a hand held propane torch that you can get from walmart. Also, if you have a stud nail gun, you can use that for heat shrinking. There is a tip used for shrinking that you can out in the stud gun.
ButlerCollision 1 year ago