S&W640 Closeup
Loading...
Link to this comment:
Uploader Comments (2guntom)
Top Comments
-
Lots of power in a small package
3 years ago 4
-
yea i agree it just looks wrong
2 years ago 2
All Comments (26)
-
@TheOl1911 I have a Model 60 Smith. It's a J-Frame .357 and I shoot mine just fine. My hand doesn't even start getting sore till I get up over 70 rounds or so (if I'm not wearing my glove that is). You just got to have some wrist strength and a steady hand( not trying to insult you by the way). J-Frame .357s are awesome carry revolvers. They're small, easily concealed, and pack a punch.
-
I carry a 642 with 110gr+p and I use to own a 340pd and my god, that thing was difficult to shoot. the 340pd using 357mag had violent recoil. I tried my best w/practicing but I never did get that good at it. With the 642 I'm fine and the recoil is not bad at all. I don't think j-frame and 357mag mix well!
-
im gonna have to disagree with you guys I love the looks of the 640 I think its a great looking gun.
-
@buzzclark on the smith&wesson hammerless models there is no need to clean under the sidecover unless it gets submerged or buried in sand [ they are truly handy little guns] in which case you'll need to remove the sidecover screws then tap your screwdriver handle on the frame with the sidecover facing UP to loosen DO NOT PRY and be careful not to lose any small parts then clean normally. good luck i would recommend any of S&Ws fine snubs. deadeye
-
nice hamerless
-
@snyper105 so do i. i like the classic look and bought Smith & Wesson .38 Special Snub Nose Airweight after seeing the variations. it's safer but doesn't look that cool without the exposed hammer.
-
Shooting low level .357s ? Recoil didn't look that much different than how my 640 jumps when I shoot +P .38's. I haven't shot .357's in it yet.
- 1:39Smith & Wesson Model 640by focusource15,429 views
- 0:14Squib Bullet Hits (Read Description!!!)by psychovisioncreation4,559,416 views
- 5:27Smith & Wesson model 60by WVCBH4,885 views
- 0:28Smith & Wesson Airweight .38 Specialby liberty05719,813 views
- 3:42SW Model 640-1 357 Magby phishst1cks2,542 views
- 0:22Matron Two .38 Snubsby fenderbmw53,472 views
- 2:52New S&W 686 .357 Magby MadOgre52,418 views
- 2:35SW 640by truewing666714 views
- 0:20S&W640by 2guntom11,292 views
- 1:17Smith & Wesson model 60 j-frame .357by ibuiltmineo1oo34,376 views
- 0:06desert eagleby bigjohn014517,200,169 views
- 1:38PC vs. MAC 357by NewIndigo16,839 views
- 6:25You Could Have Heard A Pin Drop.by ForBibletruth5,504 views
- 1:13Taurus .44 Magnum firing close upby mmSeven7723,263 views
- 6:05Just Say No To 9mm Part 2 of 2by VinnyS91419,707 views
- 2:47Shooting Mar.2-2008 - Tokarov, S&W M&P40c, S&W ...by drbilderburger4,389 views
- 7:38Thoughts on Revolversby floatingaxehead70,230 views
- 0:57Gunblast.com - Smith & Wesson Model 60 Pro .357...by Gunblastdotcom19,819 views
- 0:30Firing S&W model 327 357 magnumby quincylui26,642 views
j frame?
pjicleanair420 10 months ago
@pjicleanair420
yes
2guntom 10 months ago
Interesting the amount of pressure required. Its a very deep trigger pull. I found the video interesting, thanks for posting.
dmbphotography 1 year ago
Pressure? I'm SLOWLY pulling the trigger to keep the revolver still
2guntom 1 year ago
I just bought the 340pd is it as close to your as recoil goes?
giop69 4 years ago
No, not even close. The 640 is all stainless steel. The 340 is going to kick.
2guntom 4 years ago