Bushing Removal Without Smoke
Loading...
Loading...
2:48
Rubber control arm bushing replacement overviewby elephantracing71,176 views- 0:25
how to remove a bushingby Seisephiroth41,981 views
- 4:23
Bushing Removalby Skarpalife6,599 views
- 0:21
Bushing Removal Toolby GTO1OHIO35,416 views
- 3:45
irreplaceableby annabanana312,799,475 views
- 0:23
Manual Bushing Tool Set from Schley Products/SP TOOLSID11199by SEMAChannel3,003 views
- 1:27
Nike Spring Eye Bush Removal kitby bushingtools10,978 views
- 5:52
how to press in a bushing in an upper control arm.wmvby 7impala16,640 views
- 55 videosball joings bushin relays
- 1:22
BMW E46 rear diff bushing installby thankath26,511 views
- 4:46
jailbait teen dareby davidt198013,628,016 views
- 0:29
VERY BAD Ball Joints - WATCH THIS!!!by haglinautomotive196,405 views
- 3:21
2011 Camaro - Pressing Out Upper Control Arm Bushingby camaromodz5,020 views
- 2:49
How i made a bushing press toolby Jdmdecals19,745 views
- 0:34
Bad control arm bushing? Clicking sound. Volvo S80by macplee19,118 views
- 3:43
How To put in Polyurethane Bushings (Energy Suspension Bushings) For a 2 Gen RX-7(FC3S) Part1by MrDriftoDrifto17,913 views
- 1:26
Homemade Bush Extractor Removes and Inserts Chassis Bushesby TonyMahlony17,589 views
- 3:03
Deco Drive Betty Bangsby bettybangsmiami2,991,639 views
- 4:23
How To Remove Control Arm Bushingsby Quiroz92186,699 views
- 2:30
Removal of diff bushing with no tool.3gpby flipfinish9,937 views
Just finished upper rear control arm just like you show it in this movie.
1. The tool with the smallest sleeve does not fit. You used trickery here. I used three arem puller from Harbor Freight on these bushings. Not much pain. The tool that you show is perfect to remove and to insert bushing into spindle (rear upper outer). BTW you do not need impact wrench - I did it with ratchet in about 15-30 seconds. The pain is with inserting rubber bushings and all that lubriacting soap mess.
maciekskontakt 2 months ago
@maciekskontakt - I know what an air driven impact wrench sounds like. I've owned multiple examples. Two things can make similar sounds.... especially through video. I wasn't trying to imply that the video was fake or anything, but ok.
DaedalusZero 2 months ago
@DaedalusZero
Any impact wrench sound just like this
maciekskontakt 2 months ago
@thaik56
I thought it was cast and machined threaded rod. It looks like it. I would assume it cracks and break rather than bend. I would think control arms bend easier.
maciekskontakt 2 months ago
@cbr900rr919
Messy. Also bear in mind that burning this stuff may tick off neighbors (smally smoke and fire). Some states do not allow open fires anyway. It is just enough that people do not complain if we Seafoam engine ;)
maciekskontakt 2 months ago
Looks like Miata rear upper control arm. I am just about to go to garage and start from these to repalce with Delrins... and use just this HB tool. Encouraging, but I saw that it was slightly bending. I hope it will not bend permanently
maciekskontakt 2 months ago
stimpy! you idiot!
XKTMRiderX 4 months ago
no flames but noisy lol
jjasonell 5 months ago
just burn them out much easier and use the tool to put the new ones in lol
cbr900rr919 7 months ago
Is this tool reliable?
Some says it will bend after 2 or 3 times of use.
thaik56 7 months ago