RCPowers Extra 300 crash Death Spiral (flat spin)
Loading...
Loading...
158
views
Loading...
Uploader Comments (legoliker7517)
see all
All Comments (5)
-
e trailing tips are warped up more than the root. This makes the tips stall last, rather than first. That way it won't tip stall and spin. (this method is known as washout)
Loading...
4:04
Foam F22v2 and Dollar Tree Foam Boardby PHM001,114 views- 0:36
B-17 RC crash at Bomber Field 2011by yarsmythe4,143 views
- 4:46
Boeing Vertol 107 Absturzby HckHeesters309 views
- 1:45
RCPowers Mig-29 X-Large Jet with 70mm EDF (Part-2)by phoebehndz287 views
- 6:12
Top 30 Dyno Tuning Disasters - Car tuning gone all wrong!by ViezuRemap98,939 views
- 3:02
RC Eurofigher (RCSuperpowers V2) Raw Footageby RCChronicles165 views
- 0:49
Upright flat spin - Extra 300by acropilot30039,640 views
- 0:52
Blade 450 first flightsby daplaneflyer154 views
- 3:31
Kickin' Around the RCPowers Eurofighter v2by gstrysky174 views
- 7:08
Crash Test Hobby Grim Reaper.mp4by ElefantXPS176 views
- 1:02
EDF RC jet F86 good flying ends in small crash Worb Switzerlandby theleabres256 views
- 2:27
Twister crash.MOVby AkroPopik60 views
- 4:38
Beginner RC Airplane!by RCSuperPowers442,641 views
- 1:55
All of Rc Powers V2 planesby RCflyer729101 views
- 6:15
ALMOST CRASHED 100cc Extra 300 - Close Calls!by jethro45051,631 views
- 1:14
Nitro Harley Engine Explosion Fail at Funny Cars Under the Stars 9-10-11by robzneed4speed1,667 views
- 1:18
Amazing Extra 300 flown by Greg Poeby dolbydarma94 views
- 0:50
Mirage 2000 RC Jet crash causes Lipo battery to explodeby AdrenaCo2,390 views
- 4:20
RC plane complationby RCChronicles20 views
- 0:28
Flat spin help, what am i doing wrong?by RCBowerz565 views
yes, but add expo!!!! without it it is about two or three times as twitchy as the rcp extra 300. (trust me, i have had both) also, it is much harder to repair because the repairs are usually twice the entire weight of the original plane. buy a 4-site, fly it till it's dead, buy a micro extra 300 3d from eflite, and swap the electronics over. by the way, do you know where i could get a cheap covering iron? i am building a 4' balsa plane for either nitro or electric.
RCllamadude 3 months ago
@RCllamadude LOL OK....I'll probably just build a mini 3D plane...Try hobbyking....they have a ton of cheap stuff and electronic(you probably already know that)--I almost always buy from them
legoliker7517 3 months ago
Nice. Try steam bending the trailing edge of the wings so th
RCllamadude 3 months ago
@RCllamadude well, it was kinda tail heavy too. But if I make a new one, I'll try that. If I make another 3D plane it will probably be small like 20-25" w/s. Does your 4-site have enough power to easily hover?
legoliker7517 3 months ago