Noctua NH-D14 installation on LGA 1156 Socket | Quiet Your PC pt1 (720p)

Get the song & all noise floor sound files at http://www.yummybeats.com

SPECS:
The Noctua NH-D14 should fit in all cases with a minimum width of 20 to 21 cm (7 to 8 inch). You should be able to use all ram bars without a cooler on top (in some cases you also can remove the ram cooler). For detailed specs and a compatibility list, visit http://noctua.at

This video shows how to install the Noctua NH-D14 on an LGA 1156 Socket intel i7 (Asus P7P55E-Pro Mainboard)

WARNING: This video is not an installation manual replacement. For installation refer to your manual which comes with your Noctua cooler. We are not responsible for any damages!

Category:

Howto & Style

Tags:

• noctua
• NH-D14
• cooler
• heat
• sink
• heatsink
• install
• installation
• montage
• mounting
• mount
• intel
• i7
• LGA
• 1156
• socket
• quiet
• pc
• computer
• fan
• cooling
• noise
• blocking
• reduction
• dBA
• audio
• studio
• control
• room
• einvironment
• instructions
• gaming
• electronics

[airsoftrulzpaintball]

Would some g skill ripjaw ram fit? Its the type with half a centimeter "teeth" on them

[YummyBeatsClips]

@airsoftrulzpaintball I can't tell you definitely but it should work since you can also move up the fan a bit or mount it on the other side. Or in worst case just use another ram slot (if there are some free). Sometimes you can also dismount the ram cooler since the ram also gets the airflow of the Noctua fans. But please make sure that this is really recommended by Noctua or your ram manufacturer. You can also visit Noctua and see if your ram is supported.

[domeee11]

why would you wear latex gloves?

[YummyBeatsClips]

@domeee11 you don't have to. But if you got some latex gloves, use them. It protects the cooler/CPU from fingerprints which would reduce the cooling performance.

[halofannatic]

The actual installation begins at 3:42 Thumbs this up, it will save people almost 4 minutes of their lives.

[YummyBeatsClips]

@nobertikus hehe, thx. But to be honest it's no big deal and only what the manual tells :-) The paste gets spread perfectly by the cooler's pressure when you fasten the screws.

[overclockedamd123]

Ram bars...rofl.

[TalesOfWar]

@TheJimmyman888 Yep.

[TheJimmyman888]

would this cpu cooler work on a lga115 motherboard?, with an intel 2700k processor?

[DeadlockUser]

You forgot a RAM Clip

[ComVoiDua]

MOBO: ASUS P8Z68 V / Gen3 will post a short clip soon. Be waiting for it my good people.

[ComVoiDua]

Running 2x G Skill Ripjaw X and 2x Corsair Vengeance, running smooth so far. Yes, the Corsair Vengeance (not Low Profile version), barely past / fit.

[domeee11]

what if i hide the cable near the heatpipes and it melts down the cable covering? i just ordered my whole set of SB rig with 7970 :))

[airsoftrulzpaintball]

Actually my main problem is that i dont know if it'll fit in a zalman z9 plus

[kamigato]

@airsoftrulzpaintball I got red ripjaws with "teeth" and they fit perfectly with this cooler :)

[ComVoiDua]

Good news, Noctua NH - D14 installed with two Corsair Vengeance and two G Skill Ripjaw X Series, barely past. Wait for my clip my good people!!!