Go Kart Project Status Report 4_17_2010 Steering Complete
Loading...
Loading...
4,043
Loading...
Uploader Comments (davi200)
see all
All Comments (11)
-
make another vid please i want to follow up on these vids
-
thanks. i know that i need to work on my lighting its darker than hell.
-
thanks i know i need to work on lighting my lighsin my room are dark as hell.
-
i want to see that thing offroad what rear suspension and motor are you using
-
those lawnmower spindles will snap i had some of them on my gokart from a toro ride on
Snaped off soon as i went over a bump over 30km/h
-
is the spindle off a riding lawnmower
Loading...
4:48
my go kart part 1by firmclock26,420 views- 3:16
Go Kart Project Part 2by davi20020,082 views
- 1:22
Dirt Buggy 5: Spinlde steering armby Travitanium5,176 views
- 2:16
Go-kart steering designby GRAHAMAUS34,706 views
- 1:57
Go Kart Four Link Front Suspension Completedby davi20020,942 views
- 8:48
Go Kart Four Link Front Suspension Fabricationby davi20026,962 views
- 2:11
Go Kart Project Status Report 10-7-2009by davi2003,867 views
- 2:43
Homemade go kart steering setupby swabbster3601 views
- 0:49
Go Kart steering detailby Maclman1738 views
- 0:45
go kart part 1by mechanicojoe25,246 views
- 0:56
my homemade go kart part 1 ( frame and steering )by stephenthepilot4,828 views
- 2:20
Berg Jeep Wrangler Pedal Go-Kartby pedalcarshop8,873 views
- 0:46
12HP go kart buildby tequilasunrise156114,733 views
- 0:31
6.5 Grey Hound Engine Throttle Set Up (Go Kart)by tefjyma3,615 views
- 1:00
go kart lawn mower part 1by ryancoolryan00033,447 views
- 0:26
home made suspension on my go kart.by Edgarbopp14,053 views
- 6:26
13 HP Go Kartingby sse147820,398 views
- 1:28
Rigid frame go kart build slideshowby aussiekartman60,098 views
- 1:25
Electric Go Kart frame.mpgby amesweb859 views
Most all the parts are off of an old craftsman ridim mower. I fabricated a new axle out of tubing and used the old spindles of the mower since the wheels are going to be used too.
davi200 1 year ago
are you going to run another steering linkage to the other tire or just trust the one side? I had a buddy do the same thing you did, and his broke and caused him to flip and break an arm.
smithcycles 1 year ago
@smithcycles It's designed just like a auto's steering so it should be OK. Plus, the Kart is going to only go about 10 miles per hour or so, same speed as the riding lawnmower went. And, its got a roll cage....
davi200 1 year ago
@davi200 Looks really well built just one thing, won't it slip at the end of the shaft where the plate is between those two nuts and lock washer? Lot of pressure on that to turn and push the tie rods.
ModelKarKid 1 year ago
@ModelKarKid Hmmm. That is a good point. If it does start to slip, I could weld it in place. I chose not to do that because as it is now fabricated the entire steering shaft is removeable. Don't know why I would need to ever remove it, but you never know....
Thanks for the comment. I think its the first constructive comment I have ever received.
davi200 1 year ago