*Part 4* DimasTech Dual Test/Easy Bench v2.5
Loading...
Uploader Comments (lvl8hacker)
All Comments (23)
-
@lvl8hacker i observed that Faser white tubes u used upside are 3/8-1/2" but the other downside with the RADS, the black ones?
-
@iFlashPlays Sounds like you might be using the wrong quick disconnect fittings. You need to use the one that is threaded. It then just screws into the pass through fitting. Hope that helps
-
Thank you. I will do the same though. Very nice. Can't wait to see your Silverstone FT02 unveiled.
-
Hi! nice work, just a question! wich kind of fittings did you use? inclusive tubes everything.. ;)
-
@lvl8hacker Thanks for the response....I didn't know you were running push/pull...or at least in the video it looked just like a push config.
Regardless, I am sure it wouldn't make much difference either way.....I am very impressed by this build, looking forward to more updates. Keep up the good work!
6:23
*Part 5* Final/Completed DimasTech Dual Test/Easy Bench v2.5by lvl8hacker1,404 views- 3:55
Open Bench PC Scratch Build (Time Lapse)by blackworx1,271 views
- 1:49
*Part 2* DimasTech Dual Test/Easy Bench v2.5by lvl8hacker810 views
- 9:26
Dimastech Bench Table Easy V2.5by TimeToLiveCustoms7,071 views
- 0:48
Dimastech v2.5 Bench-table WC.by marcoszip1349 views
- 8:36
**Update Part 2** Caselabs M8 water cooled/ GTX 580 Hydro 3 way SLI/Water cooledby lvl8hacker5,791 views
- 3:51
My Antec Skeleton Computer Caseby rvr2791 views
- 3:40
Corsair Obsidian 800D Water Cooling Mod - Part 1by ego1973612 views
- 1:48
Water cooled PS3 testby khankimaghi293 views
- 3:07
Test Bench From A Old Computer Caseby SylentCommando628 views
- 0:43
DimasTech Evoby ZHRC166 views
- 7:53
Setting up the Test Bench. Sabetooth 990fx AM3+by Novix64,471 views
- 2:55
homemade computer test benchby bdkaka2,127 views
- 2:46
HP DM1 3100sa AMD E350 Benchmark Testby desaputra460 views
- 0:55
RAM DIMM Failureby acidfingers2,684 views
- 8:49
Futurelooks Unboxes the ASUS P8Z68-V PRO LGA1155 ATX Motherboardby Futurelooksdotcom4,308 views
- 3:29
*Part 1* DimasTech Dual Test/Easy Bench v2.5by lvl8hacker595 views
- 0:55
DIY Fuel Injector Test Benchby Sevillian27310,089 views
- 11:45
Intel i7 950 Reviewby TimeToLiveCustoms28,803 views
@ lvl8hacker Of all the water-cooling reservoirs, pumps and fan controllers you have usd, which do you like or have worked the best ?
Ronsanut 3 months ago
@Ronsanut By far my favorite pump is the MCP-655. I like how you can use it in a RES like the Koolance or by it self with any other RES. EK makes great stand alone RES's. I have used both the tube type and the Bay type. I like the EK spin RES due to the flow indicator. I like the Koolance for the fact I can mount 2 MCP-655 pumps on it and it takes up laees of a foot print. It really depends on how much room you have to work with.
I dont have a favorite fan controller. Just make sure it can
lvl8hacker 3 months ago
@Ronsanut cont..... Just make sure it can handle the load you are putting on it. Then it just comes down to if you like touch screens or knobs..I tend to lean to knobs on my controllers...it makes it easier for me to get them where I want them.
lvl8hacker 3 months ago
Are you pulling air from the inside of the bench or pushing through the radiators from the outside into the bench ?
Ronsanut 3 months ago
@Ronsanut The fans are in a push, pushing the outside cool air into the bench. Once all the components are installed the pushed air exhaust through the front and back. I get GREAT temps with this setup. Currently I have 2 GTX Black Ice 360mm RADS with AP-15's cooling just the CPU. The GPU that I have in there is a EVGA GTX570 SC and it is on air. I pulled the 3 way SLI GTX580 Hydros for my new build in the Silverstone FT02.
lvl8hacker 3 months ago