Blade 400 tail spin
Loading...
Uploader Comments (mrbenno72)
All Comments (7)
-
Set up your gyro again, without trim and in rate mode. Make sure you don't have the servo type set to digital. Once you get it to hold in rate mode you can flip to HH mode and you should be set. That's if you still have the issue or the heli.
-
Hi. yes I'd love some help. though i have a similiar problem. can anyone help? Why does it not centre?
-
I have, played around with the rudder trim adjustment and the tracking on the DX6i. at one stage I thought there was a problem with the transmitter, but it was not the one recalled, Iv had to put it aside for a few weeks because of an upcoming exam, but it is still not working.
nice hover vids too 32323222
-
if you go to spektrum`s web site there is a recall on the dx6i dealing with something to the affect of what you maybe exspereinceing. you may give that a shot
-
I have and it didn't make any difference. but I think I have the answer.
I was watching a video on setting up the DX6i and went to the travel adj menu and when you flick the rudder from left to right, it mostly stays on the right with intermittent bursts of left rudder despite holding it to the left. looks like it might be a switch problem.
4:52
Blade 400 gyro?by thebrunssens3,738 views- 1:41
exi and rc heli tail drifts or if heli spins solutionby wcwickedclown1,368 views
- 1:34
How not to fly a blade 400by EGO3105731,183 views
- 3:09
Blade 400 Tail belt tipsby imusbbored762,701 views
- 5:58
Blade 400 3rd flight attempt and crash.by kevdestiny20033,136 views
- 1:24
E-flite Blade 400 3D, Training and still tail/gyroby flyer15210,446 views
- 6:59
Blade 400 Trex Aluminum Head Conversionby evildomain10,333 views
- 7:23
BLADE 400 3D TAIL SETUP PART 2Aby sokal1110,734 views
- 3:15
blade 400 with upgrades stall turns & tic toc attemptsby allcalifornia3,575 views
- 2:35
How to set Tail Belt Tensionby RCHeliForum803 views
- 17 videosBlade400
- 1:22
Flying my Blade 400 3Dby MICKYDIESELS14A1,399 views
- 4:05
Blade 400 Tail Twitchby barncm558 views
- 0:48
Blade 400 trouble shooting 1of3by contact20016,300 views
- 1:43
Blade 400 Rocket Launchby barncm2,894 views
- 8:57
First outdoor flight Blade 400by rifted1,557 views
- 0:57
The Heliby videoaereo2,517 views
- 2:19
Blade 400 Practice with big(ish) crashby eRgaltube1,150 views
- 1:57
Blade 400 Custom carrier...by 00skin001,204 views
- 1:27
E-Flight Blade 400 Spinning Aroundby RCautogyro561 views
- 2:48
BLADE 400 MOD AND UP (HOVER)by ahsnw701 views
FIXED IT! - BENT TAIL ROTOR SHAFT
Disconnected the ball link underneath to move the tail fins manually, and could feel it sticking.
I reset all of the DX6i settings to the default - had a back up copy in position 10
This stopped the hard pull to one side but if you gave it any tail input it would spin really hard to either side.
The gyro settings were all screwed up, probably from me dicking around and trying everything. Reset them to defaults and......
Now it is great again!
mrbenno72 2 years ago
i have forgotten if you said you have replaced the tail servo. i was just thinking it may be burnt out if your running it in digital mode
32323222 3 years ago
It turned out there was a problem with the spektrum, and finally got it back today, charged my battery and dam it, it did the same bloody thing. I cant understand why a tail servo would burn out because it had bearly been flown. but that will be my next investigation.
mrbenno72 2 years ago
Nope, replaced the tail rotor servo tonight and same thing. I pulled the old one apart too to check the cogs, they were fine.
Next I started looking at how the tail blades pulled back and they are really slow to go to pull back from the far end of the tail shaft to the neutral position, maybe it is a bent tail shaft rod?? will replace that and see how things go.
mrbenno72 2 years ago
Thanks for your input 32323222. really appreciated it.
mrbenno72 2 years ago