Liteon 93450 c - Xbox 360 - Latest Dvd-drive - How to read and flash! Part 3

This is Part 3 of Part 3 -

Part 1 can be found here:
http://www.youtube.com/watch?v=QJs6SvfuWFw

and Part 2 here:
http://www.youtube.com/watch?v=ZSgOxZ9h2Ak


This is a short video guide I made after 5 hours of struggling, wanted to help out anyone else out there who wanna have at it with the latest 360 dvd-drive safety protocols! ;) ;)

WARNING!!! WARNING!!! If you dont have lots of soldering experience, and don't know the expressions I use in my guide, then THIS IS NOT FOR YOU TO DO! Contact a local modder to do this for you! I take no responsebility if you mess up your drive!

What you need:

** A PC with Windows XP installed + Sata onboard card.
** Power to the drive, either from an old school Connectivity kit or your Xbox 360.
** Kynar/Wire-wrapping-wire
** Cutters
** Solder iron + solder
** Lots of Solder experience
** Razor knife
** electronic tape
** Radio shack 2-pin switch
** 20 ohms resistor

Diagram: http://img706.imageshack.us/img706/5963/loboard.jpg
or relatively easier : http://www.boxxdr.com/LOHACK/LOHACK-LOW-1.jpg

Power on the drive with switch in ON position
In Jungleflasher 1.67b push Intro/Device ID, push OK for question about power cycling and no vendor ID, turn your drive off and on,
If you got a successfull vendor intro ID, put the switch in OFF position, and push READ..

Open the dumped file in TARGET window in Jungleflasher, if a Key is shown, then we're almost done.. if not, you can try and do the "oposite switch" positioning in the earlier steps, that is, OFF and then ON, instead of ON and then OFF:. it shouldnt hurt the drive, as you have the 20 ohms connected as shown in the diagram..

If the key shows up, do another dump, just to be safe, (just push READ again, or restart the whole power/read-procedure if you feel like being extra safe), if the keys match, you're good to go! Take a copy of your key!

Reconnect everything, remove all wires, clean..

Open 1.6 template in JF as target, push Manual spoofing, and paste the key from your dump. Push okey, Liteon Erase, and Write :)

The iXtreme 1.6 template is found at the usual places..

Just ask if you're wondering anything :)

For more info on how to do this, check out x-scene at

http://forums.xbox-scene.com/index.php?showtopic=697942

or http://forums.xbox-scene.com/index.php?showtopic=698256&st=0



DIAGRAM PICTURES:

http://img706.imageshack.us/img706/5963/loboard.jpg
http://img109.imageshack.us/img109/3083/2isva4z.png
http://img269.imageshack.us/img269/4536/255tn9d.jpg
http://img109.imageshack.us/img109/7520/decap.jpg

PCB pictures:

http://rapidshare.com/files/318321668/pics.rar.html

Category:

Gaming

Tags:

• 93450
• Liteon
• XBox
• 360
• flashing
• reading
• hacking
• modify
• how
• to
• jungleflasher

[joshua2030]

does this work with vista? can liteon dvd rom work?

your a good teacher

[pastorrtom]

@joshua2030 Thanks :) 

[biggreenmonsta760]

haha wow. a hacker like yourself still uses Windows 98. hahahahahahahahahaha

[pastorrtom]

@biggreenmonsta760 :P it's windows xp :P

[extacyjones]

hey my radio shack have 10m ohms is that ok.

[pastorrtom]

10m? you mean the SMD resistor? No, thats VERY tricky to solder on :)

Use PROTO_BOARDS resistors, the old fashion type :)

[NewGamestop]

u english is so BAD man!

[farazabc]

@biggreenmonsta760 lol douche bag!

[bw2project]

is this bruno?? hahaha

[waynetheguycomcast]

Alright so i was stupid as well and ripped the 101 pad off when removing the wires. Could you please help me to better understand where to solder a wire directly to the chip? Maybe a diagram or good picture.

Thank you,

Wayne

P.S. The music doesn't suck that much.

[edeeee]

Thanks for your guide, really helpful! Worked great for me except for the switch being a bit tricky.

For those of you using the 360 as power supply, I found it easiest to pull the power from the 360, replug, and turn on the console when you need to power cycle (instead of tugging at the dvd power cable).

Thanks again!

E