Buffalo WZR-HP-G300NH U-Boot boot sequence with timer

Shows the boot sequence of the Buffalo router WZR-HP-G300NH (Rev. B0 B0) with a U-Boot 1.06 (hw_rev=0, tftp_wait=4, accept_open_rt_fmt=1). TFTP server for recovery is started roughly 12 seconds after the Diag LED lights up on boot (there's roughly a 2 secs delay after plugging in power) and waits for 4 seconds.

Here's the text log:


BUFFALO U-BOOT Ver 1.06
AP83--539 (ar9100) U-boot 0.0.12


BUFFALO U-BOOT Ver 1.06
AP83--539 (ar9100) U-boot 0.0.12
64 MB
Memory Test (address line)
Memory Test start(0x00000000) end(0x04000000) size(67108864)
Data line test start:0x00000000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
Address line test start:0x00000000 len:0x4000000 pattern 0xAAAAAAAA 0x55555555
Fill test patnum:5
fill Pattern 5555AAAA Writing... Reading...
fill Pattern AAAA5555 Writing... Reading...
fill Pattern 0000FFFF Writing... Reading...
fill Pattern FFFF0000 Writing... Reading...
fill Pattern AAAAAAAA Writing... Reading...
Top of RAM usable for U-Boot at: 84000000
Reserving 275k for U-Boot at: 83fb8000
Reserving 256k for malloc() at: 83f78000
Reserving 44 Bytes for Board Info at: 83f77fd4
Reserving 36 Bytes for Global Data at: 83f77fb0
Reserving 128k for boot params() at: 83f57fb0
Stack Pointer at: 83f57f98
Now running in RAM - U-Boot at: 83fb8000
Dev ID2:2222
Dev ID3:2201
Name: AMD-SPANSION Flash id: 0x1227E, Size: 33554432 bytes.
Flash: 32 MB
In: serial
Out: serial
Err: serial
Memory Test
uboot use 83F57FB0 - 84000000
Memory Test start(80000000) end(83F00000) size(03F00000)
Pattern 00000000 Writing... Reading...
Memory Test OK
### buf_ver=[1.06] U-Boot Ver.=[1.06]
### build_date(env)=[Sep 2 2009 - 08:21:27] build_date(bin)=[Sep 2 2009 - 08:21:27]
ag7100_enet_initialize...
: cfg1 0xf cfg2 0x7114
RTL8366 series driver, reading model-id...
ID:0x6027, REV:0x6
rtl8366sr_phy_setup ethUnit=0
Realtek 8366SR switch ID 0x8366
Realtek Greeen Ethernet Setup
eth0: 02:aa:bb:cc:dd:1a
eth0 up
: cfg1 0xf cfg2 0x7114
RTL8366 series driver, reading model-id...
eth1: 02:aa:bb:cc:dd:1a
eth1 up
eth0 02:AA:BB:CC:DD:1A
, eth1 02:AA:BB:CC:DD:1A

Trying eth0
eth0 is duplex
ag7100_check_link: _100BASET
dup 1 speed 100
CFG_PLL_FREQ=5
CFG_HZ=bebc200
cpu pll=1050
eth pll=1032
eth0 clk pll=13000a44
eth0 mii=12
eth0 cfg1=f
eth0 cfg2=7115
eth0 fcfg_0=1d1f00
eth0 fcfg_1=7ff0000
eth0 fcfg_2=fff
eth0 fcfg_3=780008
eth0 fcfg_4=3ffff
eth0 fcfg_5=3ffff

tftp server(receive) go, waiting:4[sec]
Trying eth1
eth1 link down
FAIL
Trying eth0
eth0 is duplex
ag7100_check_link: _100BASET
Load address: 0x81f00000

TftpServer Timeout;
no file was loaded.
## Booting image at be060000 ...

• Category

  People & Blogs