Sensitive servo
Loading...
Loading...
18,691
Loading...
Link to this comment:
Share to:
Loading...
- 13:52
Align GP750 Gyro Setupby jasmine250167,967 views
- 10:01
Pt 1, Build an Electric Heli Training/Test Stand.by NightFlyyer184,166 views
- 7:10
Esky Belt CP doing fast forward flight, loops, tornadoesby AndY1ksi61,760 views
- 5:25
Fine Tuning Servo Set Pointby jmhrvy194736,000 views
- 5:24
Absturz mit einem Belt CP wegen massiven Funkstörungenby elcolombianogrande22,686 views
- 3:08
belt cp indoor crashby allcalifornia28,346 views
- 5:45
Belt CP V2by orangefit0768,502 views
- 6:03
setting and checking pitch part1 rcheli setupby realbigdady183,325 views
- 3:46
E-SKY Belt CP V2 Training + almost crashby GaryX100120,012 views
- 8:49
Upgrade Tips for Honey Bee King V2by jmoheli2,511 views
- 6:01
E-Sky Belt CP Direct servo to swash plate modby spooky1i200214,612 views
- 3:50
Installing a Heading Hold gyroby GaryGraham6628,305 views
- 2:35
Belt CP : GROS CRASH N°2 DANS LES ARBRES!!!!!!! :-(by yohoneybee278,562 views
- 2:28
Belt CP Heli Tail Setup Jigby HeliEye39,425 views
- 1:48
e sky head lock gyroby crazy9catears26,100 views
- 2:14
HBK 2 heli autopilotby sharonox72,647 views
- 3:12
E EKY Belt CP Gyro 0704B reglage ACby mistermac062,924 views
- 1:01
belt cp gyro futaba gy 401 problemby squaletto781,836 views
- 1:11
Head lock testby astromax801,741 views
- 0:27
BeltCP with binding headby soneebee38,571 views
Wen you use headlock mode the heli want recenter as long as you´r not in the air
RcAntax 3 years ago
lol not even half. An equal to gy401 is logictech, its cheaper and about a third of the weight too. Some say its better and you can get them on ebay for $80 if you bid right. Telebee is pretty good too
cbrian4 3 years ago
you have the gyro mounted wrong... read your damn documentation.
FatPumPumLovah 3 years ago
how good is the esky hh gyro compared to the futaba gy401 performance-wise. is it at least half as good?
buIimic 3 years ago
I have the same problem with servo sensitivity. The Gyro is placed on side with words reading upward. I have tied different servo's with same effect. Plus Head lock doesn't work properly. When switch is moved to head lock servo move to one side and will not recenter during stick deflection. Any solutions???
mmcaraway 3 years ago
Gyro must be mounted vertical,on its edge with wording reading upwards. Mount using sticky pads (to reduce vibration) as close to main shaft as poss. to sense twisting angle. Gyro senses angular motion not linear!
Gain is adjusted with signal from radio which is fixed!
To adjust manually in permanent HH mode, disconnect red wire/ connector from receiver & adjust gain using trim pot on gyro unit. +gain will increase sensitivity/temp drift as well as tailhold! Needs expo. controls really!
Lesjaye 3 years ago
It's definitely not OK to place the HL gyro like that. It should be pointing up, i.e. the words should read up pointing to the sky.
ezkamal 3 years ago
Umm maybe its cause the gyro is on its side. The helicopter should be level and the gyro should be mounted so the its on its side and the words are reading up.
retsnom92 3 years ago
Now, perhaps you have found the key to my problem, I get very large sensitivity. Your gyro is mounted on the top, and getting little input. Mine is on the side and perhaps getting too much. Curious...if I find a good place I'll let you know!
iwashypnotised 4 years ago
friend I also have the same problem and not as to even correct it you or it profit and if or iso wanted to know like? thanks.
retselc77 4 years ago