How to do-it-yourself instructional on performing an oil and filter change.
Today on Repairs101 I'd like to share with you some tips on performing your own oil changes. So have a look at my other video "Choosing Engine Oil" to help you determine exactly what kind of oil you want to put in your engine. So you can get your filter from your dealership, you can get it at a lot of different kinds of automotive supply stores and general department stores have them -- even Wal-Mart carries them. And of course if you don't know what the number is -- if you can't read it say on the filter that's on your vehicle right now -- if you don't have access to the manuals -- you get some information at the store. There's generally going to be -- at the very least -- there's going to be some flip-books attached to the shelving somehow where the filters are being sold, and in the best case scenario they'll have a parts person there to help you out. They'll just ask you a few basic questions about your car: what's the make, the model, the year and the engine size and they'll be able to help you out right away, get you the right filter right away. Perhaps have a look at one of my other videos "Safe Jacking Procedures" to give you some ideas on exactly how to lift your vehicle carefully and safely and ensure that it's safe before you get to work on it. So if you don't have the time or the equipment to actually lift the car up you can try this "curb-hopping" technique -- but if you do "curb-hopping" and you do your oil change out in the street - please don't work near a storm drain and do all that you can to catch all the oil and mop up any spills at all -- because we've had enough oil spills recently. I worked at a place that would pull the dipstick and leave it standing up like that in order to signify that the oil had been dropped. It's a drain pan. You just screw the end off of here. Do not use a pair of pliers or Vise-Grips or locking pliers, Channellocks or water-pump pliers, don't use a pipe wrench, don't use these kinds of tools. You can see the teeth on this, the steel is extremely hard and the teeth on it are very, very aggressive. They're going to chew up and round down the much softer metal of that drain plug. And they're going to leave you with a rounded drain plug that you can't remove except for to try filing it down a size using a hand-file, or welding a nut onto it. And don't use an open ended wrench. Use the ring wrench end of your combination wrench to do the job. A combination wrench is very simply a combination of an open ender wrench and a ring wrench, it's a combination. Definitely do use a combination wrench or a line wrench or a recess wrench or a gear wrench or your favourite socket wrench. I'll just get in here. Put the ring end of a combination wrench and just break it like that, bring this back under it, and then spin it off with my fingers. It's very tight here, as you can see, but I didn't jack the car up at all. We're working on it on its own wheels. So this is its natural height. "Tighten the engine oil drain plug to twenty-two foot pounds". OK now that the oil pan nut is back in place I'm going to drag the drain pan ahead a little bit to capture any oil that gets away when I remove the oil filter. This is an oil filter wrench - this is for very large sized oil filters. This is a moderate sized one for car engines and light trucks. By far the most useful is the strap wrench. If you're wondering if you have to do a filter change every time you do an oil change
Take a little bit of this old oil like that and just use it to lubricate the gasket before you install it, and that'll ensure that it comes off easily when you go to change it again next time. Tighten the new oil filter to three-quarters to a full turn after it's contacted the surface. And that's it. So you should consider this a range -- not absolutes. It should lie somewhere between the low and the full mark and if it is below the low mark then you definitely need to add oil. Perfect.
OK so do have a look at my channel, and when you're there, just ski on down to the link here, click on that link. That'll take you to my website -- go over here to the table of contents, take the slider bar and scroll right down to the bottom, and the second-last link there is called Resources/Links. This has all kinds of really great information links including a link to Faxon Automotive Literature.
Loading...
13:06
Changing the oil on the 2011 Honda Civic LX Part 1 of 2by JoeSchlubb2,522 views
What are the advantages of using the dealer OEM oil filter vs all the aftermarkets ones ? osme people say that some brands should be avoided because they're not good enough, etc... could oyu make a video on that giving your reasoning etc ?
thanks very helpfull videos you make by the way
Dicofole 6 months ago
@Dicofole - Not all filters (or other parts) are created equally so if a vehicle saw extreme service I would insist on the best money can buy.(As a side note: some aftermarket parts ARE the best money can buy!) My car sees light duty service and to save money I do choose to use some aftermarket stuff - especially filters. Like most people I like to use OEM parts when I can but AC/Delco is also a good choice for GM vehicles and so are many others.
repairs101ca 6 months ago
Most technical difficulties ever!
repairs101ca 6 months ago