Hydrogen HHO SMeyer Tubes / Cell (Triagular Arrangement)

In regards to this video. With the use of a fresh-air-pump this could be used only in the first stage if multiple stages of HHO-Containers were to be used. This would help liberate the gases from the water. It clearly keeps the fine bubbles from staying in the water, and forces them to the top of the water-bath.

This in combination with a gas vaporizer (vapor), possibly like the HYCO Device. For increased gas mileage, could make for a sure win.

With or without the vaporized gas it does cut down on some temperature. Take notice the fact it how it takes effect for a slow increase overall with high concentration of electrolyte. This helps, for short duration runs with the slow heating. Appears to of also cut down 5-10degrees of 130-140degree range(delta). So it is a start.

What ever way necessary a key to building good HHO-Cells for lasting long is keeping the temperature at the lowest levels possible. Unless otherwise proper precautions are taken for the consideration for higher temperatures. Built it tough, or otherwise it breaks.

Making use of one interesting "blue foam" found at home-depot that makes for the underside of their imitation wood flooring. Had extra after an install, peeled the sheet off and it works well for spacing the Stanley Meyer HHO Tubes.

Regards, sirHOAX

Category:

Science & Technology

Tags:

• Hydrogen
• HHO
• sirHOAX
• water
• for
• fuel
• Free
• Energy
• OverUnity
• Over
• unity
• OU
• Faraday
• PWM
• Pulse
• Width
• Modulation

[sirHOAX]

Sorry - I don't have time to debate with people who have no basis for critiquing my work. My time and energy go into these designs. If you would like to bash my work. Then please provide your own video basis for experimental evidence to prove otherwise. Please do not waste my time. Life is short, and there is no teaching an old dog new tricks. That is fact!

Zero tolerance for troll like behavior, based on potential patent pending rights and investment capital risks.

Good Day. --S--

[sirHOAX]

We have since changed the circuitry to avoid heat.

[danratsnapnames]

has anyone thought that maybe we are not breaking apart water from 1 h2o molicule, but instead, we are forcing 2m' to become 2 stable h's and 1 stable O? doesn't it take two molicules to become gas? or else isant it just a molicule of whatever. if so then think,

h2o + h2o = 2h 0 + h2o = 3 h 0 + h2o = 4h 2o

the floating molicules are not lost, but are only in flux naturaly with other molicules of forien matter that is saturated in the water.

[sirHOAX]

Yes was trying to conclude this with a friend of mine, stating possibilities of the tube arrangement creating h3. Possibly due to the positive and negative having different size surface area. Because one tube is inside the other.

[fox20012]

hats a lot of gas coming out

[cphinc1]

No one seems to be approaching the problem from Stanley Meyer's point of view his patent is available. With Radio capacitance and impedance I have experienced A phenomena called SWR what I kuynderstand is a resonant frequency in air or water as in sonar does not create heat unless the SWR is very high in which case you get no propagation of the signal.

[wsetrecords]

Straight DC will always have waste heat and will never reach efficiency without pulsation. Meyers figured that out over 25 years ago. I may not know how to do it all, I do know for an absolute fact that straight dc will never come close since it is only a linear output related to heat and amp waste. Check out my vid, using various positive and full waves, I got more hho with 1 amp than I did with dc at 15 amps. The pulse lets the bubbles rise instead of only wanting to go to one plate.

[WhiteFoot420]

ever consider thinning out the hho with the airpump & runnin a motor with it? after all, you only need to fill 20% of the combustion chamber with gas for a reliable burn. meyer talked about it in his inventions too you know.

[WolYou]

Cut down heat with air? You may keep turbulences going with the air pump, but air will keep the water from receiving heat (foam isolates). It would be better to move the tubes within the water instead of pumping air into it. Also the netto energy output is lower with an air pump.

[HHOCARCOM]

The air is also water vapor.

That will get you better engine out put.

I guess you already know that.