Quick Overview of Aaron's 2008 JG M4 S-System + Coke Can Test

Hey youtube! So this is my second video review. We are looking at the 2008 JG M4 S-System which I have lightly modified. This is not a review, I am not going to go over all the bits and pieces. This is just a look at my M4 with the following mods and what it can do.

Test in video: Poor mans chrono w/ bottom of the cans using .25g bios

2008 JG M4 S-System
-Prometheus 6.03 titebore barrel (M16 Length)
-M16 Cylinder
-Madbull Quicksilver Manufacturing Silencer
-NC Star Flashlight
-RIS Foregrip
-SPR Grip
-Leapers Red/Green Dot Scope
-Systema hop up bucking

In video: shooting .25g bios, stock 8.4v battery

PURCHASED FROM WWW.AIRSOFTGI.COM

SUBSCRIBE, COMMENT, SHARE!!!

Category:

Sports

Tags:

• M4
• JG
• S-system
• Shooting
• Can
• Test
• Silencer
• Madbull
• Leapers
• Scope
• Chrono
• 2008
• system
• Enhanced
• Version

[1037ab]

do you need a silencer? like what does it do besides look cool

[aaronyuen85]

@1037ab It's mainly for looks. In this case I used it to cover a longer than stock inner barrel. Without the silencer you would see the inner barrel protruding past the orange tip.

[StreetcatTTM]

My bad I meant the pistol grip.... Do you know how/if you can change the stock

[aaronyuen85]

@StreetcatTTM There should be videos on it which is how I learned but if I remember correctly, you pop off the end cap then you use a long screw driver to remove the super long phillips screw. After that you twist off the ring on the stock closest to the receiver of the gun. Then you lift up the tab used for adjusting stock length and slide it all the way out. Something like that. Look up a video for more details =]

[StreetcatTTM]

How'd you get the grip on been workin on that for awhile

[aaronyuen85]

@StreetcatTTM which grip? the foregrip or the pistol grip? The foregrip is a simple twist to tighten style that connects to the rail. The pistol grip requires you to open the bottom plate of the grip by removing two screws. You then drop out the motor. With the motor removed you will see two screws that you need to remove with a semi long phillips screw driver. Once those are removed, the whole grip will slide off. Reverse to install the new grip. (Make sure to set the motor back in properly) GL

[aaronyuen85]

@iknifedu o well. you probably had nothing better to do anyways...

[MLIPHANTOM22]

Were did u get the silencer. and will it fit any m4

[CrazyDayDreamer69]

you made the sport look bad with this video mate

[teamDOMIN8ORz]

lame u could just buy a 10 dollar spinger and it would still go through

[TacticalStudios]

Cool, Im getting the same scope setup as you, a red dot scope with a raiser.

[wasah50]

waouuu i just love the m4 s-system .....yours is so beautiful with all these accessories

[AIRSOFTFR34K]

Do you recommend this gun for a first AEG, because i am usually a sniper.

[TheGinger023]

I have the same gun, but its stock at the moment and is shooting low fps and having many problems with it. What would you recomend I do internally to make it have better fps? And what were the first things you upgraded internally? Cheers

[varun009]

this gun is the shit. pair it up with an m203 and a reticle sight and you're good to go.

[AirsoftPMC]

This gun is a beaut how much did modding it cost?

[STtheboy]

@1037ab also acts as a barrel extension ie increased accuracy

[dooworkk20]

@aaronyuen85

got the same rifle just wondering where u got that suppressor and does it need modifications to mount itt