CLaNZeR V-Ramp Quartz cam
Loading...
Loading...
1:31
Clanzer and the Bowman Motor Part 1by Seacrhing2008204,371 views- 2:57
CLaNZeR looking at the Flexible V-Ramp Part 5by Seacrhing200823,117 views
- 4:55
CLaNZeR looking at the Flexible V-Ramp Part 3by Seacrhing200812,973 views
- 3:40
CLaNZeR Automated PM-Orbo Rig Part 1by Seacrhing20087,808 views
- 7:10
single-Puls V-gate Magnet Motor replicationby neuberlintourist42,905 views
- 9:19
Troy Reed - magnetic motor #1by KlugManfred151,775 views
- 6:09
1-2-J.j. V-gate R33 Magnet Motor replicationby neuberlintourist19,793 views
- 1:13
V Gate Perpetual Motion Toyby jsngeorge423140,783 views
- 0:26
MAGNET MOTOR L ENERGIA INFINITA GRATIS ESISTE!!!!LEGGI !!by GIRO45761,384,838 views
- 5:35
v-gate magnet motor LIVE Part 2by carefreeforever13,898 views
- 0:12
Magnetic motor testby BETTERTOMARROW94,363 views
- 2:26
V-Gate YokeRoss Drive #1by KlugManfred104,407 views
- 0:42
03 From Dario Busch Magnetic Motor Free Energy Open Source 2_Free Energy.flvby kthedral102,004 views
- 5:35
Canestrino Magnetico con rotore a 12 magnetiniby standpir6,107 views
- 2:44
Permanent Magnet Motor V-gate Re-gauging from Roobert33by PESNetwork60,363 views
- 2:21
V Gate PM Motorby rogerwalsberg53,909 views
- 1:06
VGATE04 a YTby dietmarhohl91,595 views
- 0:19
Geomag piston engineby jaz593038,749 views
- 0:12
Propulsion magnétique - trappe en Vby flbstudio8,807 views
what if you delete the cam, and put like 5 drive bars evenly around the drum, maybe the force of the 4 drive bars will over come the "stuck" position
nottoowildbill 2 days ago
@perpetualmotion100 That won't work. Take about 50mg 80% enriched Nq-436 (weapons-grade Naquadah), mix it with a couple of drops of super-glue and put it on the cam and the rod. This mixture eliminates friction and provides the mechanical extra kick.
SH0LVA 2 days ago
what about if the bar was swung away from a backstop instead of being lifted vertically by the cam?
ultrainfinite 5 days ago
The Vgate/Vtrack WORKS via PIEZOELECTRICS, etc... It also WORKS via a BLOCK and TACKLE ! just turn the cam 180 from the gate. tye the string off at the new point at the bottom of the cam and the pulleys above to pull open the gate.fine tune. you can use cheap ceramic magnets.etc...etc...WE have NOT ! needed gasoline since 1969.see for your self... STOP POVERTY and the GASOLOONS ! not to mention SLAVERY!
perpetualmotion100 5 days ago
the weight create so much friction
hadith04 1 week ago
i think the baricentre is too off.
it loses lots of energy just on the way back up. otherwise very good :)
bluetrilobite 2 weeks ago
why not make the wheel alot bigger, that way you get a little more torque/speed going?
vindigga6 4 weeks ago
why not use magnets to lift up the thing?
OnlyCopyRight 2 months ago
1." V" The magnet possibly misprints, in the movie contains errors the beginning end to the terminal concurrent design, correct will be must wrong miss can transfer
2. magnet the magnetic force to be away from essential takes above 5 centimeters, will be separated from the magnetic force strength completely, in the movie above pulls the arm not to be away from 夠, please try to elongate an effect to be good
telepaq2000 2 months ago
You need a magnet in your bar and a magnet on the underside so when the arm hits it it will raise the bottom magnet giving the vgate enough force to clear the top bar once again...and the top bar forcing the arm to the low position again ;-) try that and repost.
simulanics 3 months ago